Download Print this page
Whirlpool LEV4634JQ Installation Instructions Manual
Whirlpool LEV4634JQ Installation Instructions Manual

Whirlpool LEV4634JQ Installation Instructions Manual

Installation instructions

Advertisement

Quick Links

Havequestions a bout y ourdryer?
Check your Use and Care Guide for a toll-free number to call, or call your
dealer. The dealer is listed in the Yellow Pages of your phone directory
under "Appliances -- Household -- Major -- Service and Repair."
When you call, you will need the dryer model number and serial number.
Both numbers are on the model/serial rating plate located in the door well
behind the dryer door and on front of opening.
Record the numbers
here for handy reference:
Model No,
_
__
_J,/_'/'/_
Serial No
Movingdryer to a newIocatzon?
Check with a licensed electrician to confirm that supply voltage at new
home matches voltage specified on the model/serial
rating plate.
Shut off electrical supply to dryer. Unplug
power supply cord and tape it securelyto dryer.
(Or disconnectpower supplycable from dryer.)
\
door to
panel.
ElectricDryer
Pa_ No. 3978844
Slide dryer onto cardboard or hardboard
before moving it across the floor to
prevent damaging floor covering.
leveling
legs all the
way in.
IMPORTANT:
Readandsavetheseinstructions.
Installer:
Leave installation Instructions with homeowner.
Homeowner:
Keep Installation instructions for future reference.
For best performance,
install dryer according to
Installation Instructions. Failure to complete installation
as instructed could void warranty.
Save Installation Instructions for local electrical inspector's use.

Advertisement

loading
Need help?

Need help?

Do you have a question about the LEV4634JQ and is the answer not in the manual?

Questions and answers

Summary of Contents for Whirlpool LEV4634JQ

  • Page 1 Havequestions a bout y ourdryer? Check your Use and Care Guide for a toll-free number to call, or call your dealer. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -- Household -- Major -- Service and Repair." When you call, you will need the dryer model number and serial number.
  • Page 2: Recessed Area/Closetinstallation

    Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches above the floor for a garage installation. Failure to do so can result in death, explosion, fire, or burns. Forproperdryingperformance: The location must provide: b/Protection from weather and water: Do not I/Level...
  • Page 3 Mobile home installation Important: Observe all governing codes and ordinances. requirements A dryer must be exhausted outdoors. Moisture and rint indoors may cause: If codes permit, this appliance is suitable for mobile home installations. The installation of • Lint to gather around the dryer where it can de fuel for a fire.
  • Page 4 See installationstepsfor details. Check operation. Turn on power supply. Check that Remove tape, dryer is level. Disconnect power supply. Change door Make electrical connection. swing. Install feet. SLIDE DRYER ONTO CARDBOARD OR Connect vent to HARDBOARD BEFORE dryer. MOVING ACROSS TO PREVENT FLOOR DAMAGE.
  • Page 5: Power Supply Cord

    Power supply cord Direct wire Fire Hazard Fire Hazard Use a new UL approved 30 ampere Use fO gauge solid copper wire. power supply cord. Use a UL approved strain relief. This dryer is manufactured with the cabinet-ground Use a UL approved strain relief. Disconnect power before making conductor connected...
  • Page 6 Three-wire receptacle Where local codes permit connecting cabinet-ground conductor to neutral wire: Loosen or remove block screw, _. Connect the neutral wire center) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw• 6. Connect the other wires to outer _ terminal block screws.
  • Page 7 Available on Super-wide side-swing and Large side-swing door models only• Open dryer door. Remove bottom If not reversing door swing, skip ahead to "Level screws from cabinet side of hinges (B). Loosen and exhaust dryer" steps. (do not remove} top screws from cabinet side of hinges.
  • Page 8 Plug power supply cord into grounded outlet or connect direct wire to power supply. Turn power supply on. m Read the Use and Care Guide to fully understand your new dryer. Select a full heat cycle (not the air cycle) and start dryer. After five minutes, open dryer door.
  • Page 9 Dryer power supply cord must be: [Toolsneeded: Dura Safe vent products can be purchased from your • U.L.-listed • 30-ampere dealer or by calling Whirlpool Parts & Accessories • 120/240-volt • Type SRD or SRDT • 1/4" nut driver or •...