Troubleshooting - Kenmore 8674 - Elite HE3 Steam 7.2 cu. Ft. Electric Dryer Use And Care Manual

TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Dryer will not run
• Has a fuse blown, or has a circuit breaker tripped?
There may be 2 fuses or circuit breakers for the dryer. Check
that both fuses are intact and tight, or that both circuit
breakers have not tripped. Replace the fuse or reset the
circuit breaker. If the problem continues, call an electrician.
• Is the correct power supply available?
Electric dryers require 240-volt power supply. Check with a
qualified electrician.
• Was a regular fuse used?
Use a time-delay fuse.
• Is the dryer door firmly closed?
If the top of the door does not latch when you push the start
button, the control will beep 3 times. Open door, reclose
firmly and start the dryer.
• Was the Start button firmly pressed?
Large loads may require pressing and holding the Start
button for 2-5 seconds.
No heat
• Has a fuse blown, or has a circuit breaker tripped?
The drum may be turning, but you may not have heat. Electric
dryers use 2 fuses or circuit breakers. Replace the fuse or
reset the circuit breaker. If the problem continues, call an
electrician.
Confirm the power cord is properly installed. Refer to
"Electrical Connection" for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, consult a qualified electrician.
The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display. The
Estimated Time Remaining will return on the display.
"AF" Diagnostic Code. The dryer vent may be crushed or
blocked.
Check the following:
Check to see if the vent run from the dryer to the wall is
crushed.
Confirm the vent run from the dryer to the wall is free of lint
and debris.
Confirm the exterior vent exhaust hood is free of lint and
debris.
Confirm your vent system falls within the recommended run
length and number of elbows for the type of vent you are
using. Refer to "Plan Vent System" for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, have your entire home venting run
cleaned.
The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display. The
Estimated Time Remaining will return on the display.
Unusual sounds
• Has the dryer had a period of non-use?
If the dryer hasn't been used for a while, there may be a
thumping sound during the first few minutes of operation.
• Is a coin, button, or paper clip caught between the drum
and front or rear of the dryer?
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
• Are the four legs installed, and is the dryer level front to
back and side to side?
The dryer may vibrate if not properly installed. See the
Installation Instructions.
• Is the clothing knotted or balled up?
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.
Dryer displaying code message
• "PF" (power failure), check the following:
Was the drying cycle interrupted by a power failure?
Press and hold START to restart the dryer.
• "F" Variable (F1, F2, F20) service codes:
Call for service.
"L2" Diagnostic Code. The drum will turn, but there may
be a problem with your home power supply keeping the
dryer's heater from turning on.
Check the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or circuit
breakers. Replace the fuse or reset the circuit breaker.
Clothes are not drying satisfactorily, drying times are too
long, or load is too hot
• Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See
"Venting Requirements."
28