Error Code Chart - Frigidaire AGQ7000EE - 5.8 cu.ft. Affinity Gas Dryer Datasheet

Error
code
E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E21 Water not pumping out fast enough.
E23 Drain pump relay on control board failed, wire off pump or pump
defective.
E24 Drain pump relay on control board failed.
E31 Pressure sensor not communicating with control board.
E35 Pressure sensor indicates water overfill.
E36 Console control board problem.
E38 Air chamber clogged or pressure sensor defective.
E41 Control board thinks the door switch is open.
E43 Console control board thinks the door locking device has failed.
E44 Console control board problem.
E45 Console control board problem.
E46 Console control board problem.
E47 Console control board thinks the door PTC circuit is open in spin. Refer to test (7).
E48 Console control board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E56 High motor current.
E57 High current on inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink caused by overloading.
E5B High temperature on heat sink.
E5C High temperature on heat sink.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E66 Heating element relay failure.
E67 Input voltage on microprocessor incorrect.
E68 Current leakage to ground on heater or fuse opened.
E71 Wash NTC failure.
E74 Wash temperature does not increase.
E75 Water temperature sensor circuit.
E82 Console control board problem.
E83 Console control board problem.
E91 Comunnication error between UI board and console control board. Refer to test (16).
E93 Console control board problem.
E94 Console control board problem.
E95 Communication error.
E97 Console control board problem.
E98 Console control board problem.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC.
EB3 Incoming line voltage below 90 VAC.
EBE Console control board problem.
EBF Console control board problem.
EF1 Clogged drain pump.
EF2 Too much soap.

Error code chart

Fault condition
2
Check
Refer to test (1).
Refer to test (2).
Refer to test (3).
Replace console control board, wire or
pump.
Replace console control board.
Refer to test (4).
Refer to test (5).
Replace console control board.
Check air chamber, rpl press. sensor.
Refer to test (6).
Refer to test (7).
Replace console control board.
Replace console control board.
Replace console control board.
Refer to test (7).
Refer to test (8).
Refer to test (9).
Refer to test (9).
Refer to test (9).
Refer to test (10).
Test first-if bad-rpl speed control brd.
Replace speed control board.
Replace speed control board.
Refer to test (11).
Refer to test (11).
Refer to test (11).
Refer to test (14).
Refer to test (15).
Refer to test (14 & 15).
Refer to test (15).
Wire off NTC - rpl water valve.
Refer to test (12).
Replace console control board.
Replace console control board.
Replace console control board.
Replace console control board.
Replace console control board.
Replace console control board.
Replace console control board.
Refer to test (13).
Check voltage at outlet. If < 130VAC,
replace the console control board.
Check voltage at outlet. If > 90VAC,
replace the console control board.
Replace console control board.
Replace console control board.
Unclog the drain pump.
Advise customer to reduce the amount
of soap they are using.