Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Directed Electronics K10
Summary of Contents for Directed Electronics K10
-
Page 1: Installation Guide
Model K10 installation guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. -
Page 2: Table Of Contents
table of contents primary harness (H1) wire connection guide ........4 primary harness (H1) wiring diagram . -
Page 3: Primary Harness (H1) Wire Connection Guide
primary harness (H1) wire connection guide primary harness (H1) wiring diagram The primary harness supplied with this unit is the standard 12-pin harness used. Two wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging and exchanging control units and connecting the necessary wires to the vehicle. - Page 4 H1/2 WHITE (-) Parking Light Output This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light control wires in Toyota, Lexus, BMW, some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights.
- Page 5 H1/6 BLUE (-) 200 mA Second Unlock Output The H1/6 BLUE output is used for progressive unlock. A progressive unlock system unlocks the driver's door when the unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again within 15 seconds after unlocking the driver's door.
- Page 6 H1/11 RED (+)12V constant power input Before connecting this wire, remove the supplied fuse. Connect to the positive battery terminal or the constant 12V supply to the ignition switch. N N O O T T E E : : Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the fuse in the har- ness for this purpose.
-
Page 7: Door Lock Harness (H4), Wire Connection Guide
door lock harness (H4), wire connection guide Green H2/A Empty H2/B Blue H2/C I I m m p p o o r r t t a a n n t t ! ! The door lock outputs are low current and should not be attached directly to any high current device;... -
Page 8: Pro Security Programmer Interface, 3-Pin Port
CONTROL MODULE Pro Security Programmer interface, 3-pin port The BLACK three-pin port is provided for programming of the unit. When using the Pro Security Programmer, it is possible to configure any and all of the programmable functions. For more information please refer to the guide packaged with the programmer. module programming The System Features Learn Routine dictates how the unit operates. - Page 9 Transmit. The transmitter is used to select the desired setting. As shipped, the unit is configured to the LED ON settings. These are the default settings. Pressing the lock button will set it to the LED ON setting. The LED will light solid (stop flashing) to indi- cate the setting.
-
Page 10: System Features Menus
system features menus Feature Default LED ON Setting Number (Press Channel 1) Active arming Chirps ON Ignition-controlled door lock ON Ignition-controlled door unlock ON Active locking Ignition-controlled domelight ON 0.8 second door lock pulses Double pulse unlock OFF Security features ON Code Hopping ON feature descriptions 1 ACTIVE/PASSIVE ARMING: When active arming is selected, the starter kill will arm (if connected) -
Page 11: Remote Coding
8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two nega- tive pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positive pulses instead of a single pulse. - Page 12 Channel Number Function Arm/Disarm/Panic Silent Mode/Remote Override/Trunk Release Remote engine start or Other Accessory Arm only Disarm only Panic only Auto-learn Single Button Arm/Disarm Configuration* Auto-learn Standard Configuration* Delete all remotes **NOTE: For Auto Learn Configurations, see Remote Configurations section of this guide. Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to sep- arate buttons on the remote control.
-
Page 13: Remote Configurations
remote configurations The transmitters can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Remote Coding. standard configuration A remote that uses the standard configuration operates similarly to many factory keyless entry remotes. A standard configuration remote allows arming, disarming, and panic mode activation with separate buttons. -
Page 14: Power-Up
power-up Power-up ensures that the when the system is powered up it will return to the same state it was in when power is disconnected. For a full description of power-up refer to the owner's manual. -
Page 15: Wiring Quick Reference Guide
wiring quick reference guide Pro Security Programmer ™ ® Override Switch 3-Pin 2-Wire Door Lock Harness... - Page 16 Get Started Get Protected Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2003 Directed Electronics, Inc. - All rights reserved GK10 11-03...
Need help?
Do you have a question about the K10 and is the answer not in the manual?
Questions and answers