Advertisement
Quick Links
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T34067 No. 5 14" Legacy Jack Plane
is designed for smoothing and flattening wood
in preparation for truing and edge jointing. The
included steel blade has a 2" cutting width sharp-
ened to a 45° bevel. This plane has a 14" cast iron
sole, stainless steel fixtures, anodized aluminum
cheeks and knob, and a solid wood tote that can
be adjusted to accommodate a variety of hand
sizes. This jack plane also features an adjustable
frog, depth adjustment knob, and lateral adjust-
ment screws for fine-tuning hard and soft wood
finishes.
Figure 1. Model T34067.
Specifications
Bedding Angle ......................................... 45 deg.
Blade Bevel Angle ................................... 45 deg.
Blade Width .................................................. 2 in.
Blade Construction ...................................... Steel
Sole Length .................................................14 in.
Sole Construction ..................................Cast Iron
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
COPYRIGHT © OCTOBER, 2024 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
(FOR MODELS MFD. SINCE 10/24) SG23365 PRINTED IN INDIA
***Keep for Future Reference***
MODEL T34067
NO. 5 14" LEGACY
JACK PLANE
INSTRUCTIONS
To reduce your risk of
serious injury, read this
entire
using tool.
Blade/Plane Iron
Lever Cap
Cam
Lever
Cap
Knob
Lateral
Adjustment
Lever
Cheek
Mouth
Toe
Figure 2. Identification.
manual
BEFORE
Chip Breaker
Tote
Depth
Frog
Adjustment
Knob
Heel
Sole
Throat
V1.10.24
Advertisement
Related Manuals for Grizzly T34067
Summary of Contents for Grizzly T34067
- Page 1 MODEL T34067 NO. 5 14" LEGACY JACK PLANE INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction The Model T34067 No. 5 14" Legacy Jack Plane is designed for smoothing and flattening wood To reduce your risk of in preparation for truing and edge jointing.
- Page 2 Rotate depth adjustment knob (see Figure 4) clockwise to lower blade, or counterclockwise to raise blade. Securing Workpiece The Model T34067 requires two hands to prop- Note: Length of blade protruding from sole erly control, so it is highly recommended to use determines depth of cut.
- Page 3 Tighten (2) locking screws to secure frog, Adjustment then assemble blade components (see Steps Screw 4–5 of Replacing Blade on Page 4). Locking Screw (1 of 2) Figure 5. Frog position components. Model T34067 (Mfd. Since 10/24)
- Page 4 (see cam is firmly secured. Figure 8). Note which sides face up. Lever Cap Keyhole Location Lever Cap Screw Blade Blade Lever Cap Screw Chip Breaker Figure 8. Blade replacement components. Model T34067 (Mfd. Since 10/24)
- Page 5 Adjusting Hand Placement Using Jack Plane The Model T34067 features an adjustable knob Workpiece security, tool handling, operator stance, and tote to accommodate a variety of hand sizes and proper tool setup all contribute to the final fin- and positions.
- Page 6 If planing pressure alters blade depth during • cuts, tighten adjustment screw after setting blade depth to remove backlash. Model T34067 (Mfd. Since 10/24)
- Page 7 Figure 16. T23877 Bench Planes DVD & Book. Figure 14. Japanese water stones. Model T34067 (Mfd. Since 10/24)
- Page 8 WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Need help?
Do you have a question about the T34067 and is the answer not in the manual?
Questions and answers