Advertisement
Quick Links
Advertisement
Related Manuals for SMARTWINGS Premium Skylight Day/Night Cellular Shade Hazel
Summary of Contents for SMARTWINGS Premium Skylight Day/Night Cellular Shade Hazel
- Page 1 Installation Guide Premium Skylight Day/Night Cellular Shade Hazel INS-102-C075 A-01 May 2025...
- Page 2 This manual uses images of the lithium battery version for installation instructions. The installation process is the same for AC and DC versions. Note: AC and DC versions do not have a Type-C charging port. lithium battery version...
- Page 3 TABLE OF CONTENTS 1. Preparation ............1 2. Shade Assembly ..........2 ............6 3. Quick Start .......... .11 4. Shade Installation Inside Mount ..............12 Outside Mount ..............13 5. Shade Charging ..........14 6. Remote Holder Installation ......18...
- Page 4 Required Tools for Installation： Included In the Package： Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade. Top Rail Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade.
- Page 5 Shade Assembly Initial Frame Assembly and Connector Integration Step 1: Position the four rails correctly according to the sticker instructions, as shown in the diagram. Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade. Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade.
- Page 6 Shade Assembly Important: Make sure the two sliding channels on the left side rails are positioned at the outermost ends before installation. Step 3: Align the four tabs of the left side rail with their corresponding slots on the shade frame.
- Page 7 Shade Assembly Step 5: Follow the same procedure as Step 3 for the right rail (B1 and B2). Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade. Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade.
- Page 8 Shade Assembly Step 7: Remove the Velcro strips. Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade. Note: Remove the C-shaped Note: Remove the C-shaped foams before using the shade. foams before using the shade.
- Page 9 Quick Start Opening the cover plate Pry open the cover plate on the top rail along its edge as shown in the illustration, then remove it. Each battery motor from original manufacturer is factory-preprogrammed and set to "Sleep Mode" before shipping to prevent any unintended operation. Before setup and operation, it's essential to "Wake"...
- Page 10 Quick Start To select a different remote channel for pairing with the motor(s) later on, follow these steps: 1. Selecting Channel Within 10 secs Press 2. Pairing Remote To Motor (2 secs) SECS Within 10 secs of Note:The motor jogs twice.Remote was added successfully。...
- Page 11 Quick Start 3. Setting Limits NOTE: Each motor is factory preset with limits by trained personnel. If you need to reset the limits, please follow the instructions below. Automatic limit setting when encountering obstacles. NOTE: If the limits have not been set, the red light will flash three times each time the UP or DOWN button is pressed.
- Page 12 Quick Start Entering Smart Pairing Mode Pairing Method 1: Press and hold the P1 button on the motor head for 6 seconds. The motor will jog twice, and a red LED light will illuminate, indicating the motor is in pairing mode and ready for app connection. Pairing Method 2: 1.
- Page 13 Quick Start Checking Screws and Reattaching Cover Plates 1. Remove the bottom cover, then check that all assembly screws on both the upper and lower sides are securely tightened. 2. Reattach both the upper and lower cover plates to their original positions, ensuring no wires are pinched during installation.
- Page 14 Shade Installation Before Installation Before installing the skylight shade, if using the lithium battery version with solar panel, make sure the charging cable is routed downward for future connection. For AC or DC versions, route the power cable toward the nearest power outlet on either side for easy access later.
- Page 15 Shade Installation Inside Mount Installing the Skylight Shades Step 1: Position the assembled skylight shade in its intended location. Insert screws through the pre-drilled holes on the left and right rails to secure to the wall. For wooden frames, pointed screws can be driven in directly For concrete frames, pre-drill holes with a masonry bit, insert...
- Page 16 Shade Installation Outside Mount Installing the Skylight Shades Step 1: Remove the cover plates from the top and bottom rails. Position the skylight shade correctly, and insert screws into the designated mounting block locations as shown in the diagram.
- Page 17 Shade Charging Power Supply Method One: Magnetic Type-C Charging Cable (for Lithium Battery Only) Step 1: Plug the magnetic cable head into the Type-C port on the cover plate. Step 2: To charge, bring the magnetic Type-C charging cable close to the connector — it will automatically attach.
- Page 18 Shade Charging Power Supply Method Two: Solar Panel (for Lithium Battery Only) Step 1: Connect the solar panel to the charging cable on the back of the shade. Step 2: Place the solar panel behind the shade and adhere it to the glass to remain hidden from view.
- Page 19 Shade Charging Power Supply Method Three: AC Power Supply Step 1: Plug the adapter into a nearby wall outlet. Ensure the power cable does not run across or through the moving parts of the shade.
- Page 20 Shade Charging Power Supply Method Four: DC Power Supply Step 1: Plug the adapter into a nearby wall outlet. Ensure the power cable does not run across or through the moving parts of the shade. White Black...
- Page 21 Remote Holder Installation...
Need help?
Do you have a question about the Premium Skylight Day/Night Cellular Shade Hazel and is the answer not in the manual?
Questions and answers