D-Link DWL-P200 Quick Installation Manual

DWL-p200
Quick installatio
Quick installatio
SpecificationS/ featureS
power over ethernet adapter
Quick installation Guide
minal Unit
Network Device
proDuct Setup
proDuct Setup
proDuct Setup
Switch
3
Switch
Switch
connect to network Device
новного
Insert one end of DC Power Cable that is
1
provided into the Terminal Unit, and the other
ального
end into the DC of Network Device. The Power
LED of Terminal Unit should light up. connect to Base unit
Connect the provided Cat5 Ethernet cable from
Insert one end of Cate5 Ethernet RJ-45 cable into the "Lan in" port
кабель
Terminal Unit "Lan out" to RJ-45 LAN port of
of Base Unit. Plug one end of the Power Adapter into the "Dc 48V
1
Network Devices
in" Base Unit and the other end into your electrical outlet. The green
новного модуля
1
"Power" LED on the Base Unit should light up.
го модуля.
(Do Not mistake the "Lan in" port with the "poe" port. Incorrectly
plugging the wrong Ethernet cable into the wrong Ethernet port may
напряжения,
connect to Base unit
cause serious damage to your devices. D-Link will not replace or
connect to Base unit
а выходе 5 В
repair products or reimburse customers for devices that become
damaged due to incorrect installation, nor is liable for any loss of
2 В постоянного
Insert one end of Cate5 Ethernet RJ-45 cable into the "Lan in" port
business resulting in the incorrect installation of this product.)
Insert one end of Cate5 Ethernet RJ-45 cable into the "Lan in" port
ебований
of Base Unit. Plug one end of the Power Adapter into the "Dc 48V
• Temperature
of Base Unit. Plug one end of the Power Adapter into the "Dc 48V
SpecificationS/featureS
зуйте только
Operating: 0°C to 40°C ( 32°F to 104°F)
in" Base Unit and the other end into your electrical outlet. The green
Storage: -10°C to 70°C ( 14°F to 158°F)
гории 5).
in" Base Unit and the other end into your electrical outlet. The green
"Power" LED on the Base Unit should light up. • Operating Humidity : 10%-80%
• Cat5 Pin Usage: Data 1, 2, 3, 6. Power 4, 5, 7, 8
"Power" LED on the Base Unit should light up.
• Voltage: Input 48VDC 500mA. Output 5VDC 2.5A
(Do Not mistake the "Lan in" port with the "poe" port. Incorrectly
or 12VDC 1A
(Do Not mistake the "Lan in" port with the "poe" port. Incorrectly
ificationS/ featureS
• Ethernet: 10/100Mbps
plugging the wrong Ethernet cable into the wrong Ethernet port may
plugging the wrong Ethernet cable into the wrong Ethernet port may
cause serious damage to your devices. D-Link will not replace or
Network Device
cause serious damage to your devices. D-Link will not replace or
inStaLacion De proDucto
repair products or reimburse customers for devices that become
repair products or reimburse customers for devices that become
damaged due to incorrect installation, nor is liable for any loss of
damaged due to incorrect installation, nor is liable for any loss of
business resulting in the incorrect installation of this product.)
льный модуль: 134 г
Switch
Network Device
Terminal Unit
DC OUT
Power
LAN Port
3
DC 48V IN
LAN OUT
Подключение к сетевому
LAN IN
устройству
Подключите кабель питания постоянного тока,
входящий в комплект поставки, к терминальному
модулю и к разъему питания сетевого устройства.
Индикатор Power на терминальном модуле
должен загореться. Подключите входящий в
комплект поставки кабель Ethernet категории 5 к
порту "Lan out" терминального модуля и к порту
LAN RJ-45 сетевого устройства.
Terminal Unit
DC OUT
Power
DC 48V IN
УстаНОВка
DC OUT
Switch
Power
LAN Port
Base Unit
1
DC 48V IN
Base Unit Подключение к основному м
DC 48V IN
Подключите Ethernet-кабель RJ-45 категории 5 к по
основного модуля. Подключите адаптер питания к
2
48V in " основного модуля и к электрической розет
индикатор "Power" на основном модуле должен заг
connect Base unit and
путайте порт "Lan in " с портом "poe". Подключени
terminal unit
к некорректному порту Ethernet может привести к с
повреждению устройств. Компания D-Link не произ
Connect another Cat5 Ethernet cable
или ремонт устройств, не возмещает расходы поль
LAN IN
from Base Unit "poe" to the "poe" of
устройства, которые были повреждены из-за некор
LAN IN
Terminal Unit.
и не несет ответственности за утрату деловых возм
Use Select Voltage to set DC output
вследствие некорректной установки данного устро
to 5V/2.5A or 12V/1A as required by
the Network Device.(Only use a Cat5
Характеристики
Ethernet straight through cable)
• Используемые контакты кабеля Ethernet катег
Данные 1, 2, 3, 6. Питание 4, 5, 7, 8
• Напряжение: Вход 48 В постоянного тока 500
В постоянного тока 2,5 А или 12 В постоянного
• Dimensions: Base(Terminal) Unit:
83.26 × 52.92 × 28.25 mm
• Weight: Base + Terminal Unit : 134 gram
configuração D
• Температура
Рабочая: от 0°C до 40°C
Switch
Хранения: от -10°C до 70°C
• Рабочая влажность: 10%-80%
Base Unit
Terminal Unit
Terminal Unit
LAN OUT
PoE PoE
Base Unit
Base Unit
Terminal Unit
DC 48V IN
LAN IN
Speci
DC 48V IN