1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Switch
  5. ISE70
  6. Instruction manual

SMC Networks ISE70 Instruction Manual

Hide thumbs Also See for ISE70:

Advertisement

Table of Contents

ISE70_71-TF2Z062EN
Instruction Manual
High Precision Digital Pressure Switch
ISE70/71
The intended use of the pressure switch is to measure and display the
pressure of fluid and to provide an output signal.
1 Safety Instructions
These safety instructions are intended to prevent hazardous situations
and/or equipment damage. These instructions indicate the level of
potential hazard with the labels of "Caution," "Warning" or "Danger."
They are all important notes for safety and must be followed in addition
to International Standards (ISO/IEC)
*1)
ISO 4414: Pneumatic fluid power - General rules relating to systems.
ISO 4413: Hydraulic fluid power - General rules relating to systems.
IEC 60204-1: Safety of machinery - Electrical equipment of machines.
(Part 1: General requirements)
ISO 10218-1: Manipulating industrial robots -Safety. etc.
• Refer to product catalogue, Operation Manual and Handling
Precautions for SMC Products for additional information.
• Keep this manual in a safe place for future reference.
Caution
Warning
Danger
• Always ensure compliance with relevant safety laws and
standards.
• All work must be carried out in a safe manner by a qualified person in
compliance with applicable national regulations.
• This product is class A equipment intended for use in an industrial
environment. There may be potential difficulties in ensuring
electromagnetic compatibility in other environments due to conducted
or radiated disturbances.
Otherwise electric shock, malfunction or product damage can result.
• Refer to the operation manual on the SMC website (URL:
https://www.smcworld.com) for more safety instructions.
ORIGINAL INSTRUCTIONS
Caution indicates a hazard with a low level of risk which, if
not avoided, could result in minor or moderate injury.
Warning indicates a hazard with a medium level of risk
which, if not avoided, could result in death or serious injury.
Danger indicates a hazard with a high level of risk which, if
not avoided, will result in death or serious injury.
Warning
*1)
, and other safety regulations.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ISE70 and is the answer not in the manual?

Questions and answers

Related Manuals for SMC Networks ISE70

Summary of Contents for SMC Networks ISE70

  • Page 1 ISE70_71-TF2Z062EN ORIGINAL INSTRUCTIONS Instruction Manual High Precision Digital Pressure Switch ISE70/71 The intended use of the pressure switch is to measure and display the pressure of fluid and to provide an output signal. 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

  • Page 2: Specifications

    Data storage function Available Event function Available Vendor ID 131 (0x0083) ISE70-*-L2-* : 307 (0x0133) Device ID ISE71-*-L2-* : 308 (0x0134) Warning Special products (-X) might have specifications different from those shown in this section. Contact SMC for specific drawings.

  • Page 3: Installation

    3 Names of Individual parts 3.1 Product Power supply / Output connector (M12 plug) Display Fitting (24 mm across flats) 3.2 Display Part Description Operation Light Displays the switch operating condition Displays pressure measurement values and Main display error codes (2 colour display). Sub display (left) Displays items (Orange) Displays set values, peak and bottom values.
  • Page 4 4 Installation (continued) 4.4 Piping Caution • Before connecting piping make sure to clean up chips, cutting oil, dust. • After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting (24 mm A/F). • When tightening, do not hold the upper part of the product (display) with the spanner.

  • Page 5: Setting (Measurement Mode)

    If this condition is acceptable, then keep these settings. Default setting for Pressure range Item ISE70 ISE71 [P_1] Set value of OUT1 [MPa] 0.500 0.800 [H_1] Hysteresis of OUT1 [MPa] 0.050...

  • Page 6: 3 Step Setting Mode

    7 3 Step Setting mode • 3 step setting mode (hysteresis mode) In 3 step setting mode, the set value (P_1 or n_1) and hysteresis (H_1) can be changed. Set the items on the sub display (set value or hysteresis) using the UP and DOWN button. When changing the set value, follow the operation below.

  • Page 7: Function Selection Mode

    9 Function Selection mode In measurement mode, press the SET button between 3 and 5 seconds to display [F 0]. Select to display the function to be changed [F□□]. Press and hold the SET button for 2 seconds or longer in function selection mode to return to measurement mode.

  • Page 8: Troubleshooting

    12 Troubleshooting 12.1 Error Indication Error Error displayed Description Measures Turn the power off The load current and remove the Over applied to the switch cause of the over current output has exceeded current. error the maximum value. Then supply the power again.

This manual is also suitable for:

Ise71

Table of Contents