Related Manuals for POP UP MI TOWER +
Summary of Contents for POP UP MI TOWER +
- Page 1 I N S T R U C T I O N M A N U A L FOR M I TOWER + TOWER+ INSTRUCTION MANUAL EN 1004-2-en (Rev.07-03-03-2025) info@popupproducts.co.uk popupproducts.co.uk +44 (0)1244 833 933...
-
Page 2: Table Of Contents
I N S T R U C T I O N M A N U A L F O R M I TOW ER+ CONTENTS CONTENTS GETTING STARTED INTRODUCTION MITOWER+ 2M - ASSEMBLY KNOW YOUR MITOWER+ MITOWER+ 3M - ASSEMBLY KNOW YOUR MITOWER+’S COMPONENTS MITOWER+ 4M - ASSEMBLY KNOW YOUR KIT LIST AND SPECIFICATIONS... -
Page 3: Introduction
Only original Pop Up Products MI TOWER+ components, in undamaged condition as specified in this instruction manual, shall be used to assemble this access tower. Pop Up Products Limited cannot accept responsibility in the event of an accident occurring because of mixing components from different manufacturers. -
Page 4: Know Your Mitower
KNOW YOUR MI TOWER+ PA R TS LI S T I N G 4 RUNG FRA ME ADJUSTAB LE LEG AND CASTOR TOE BOA RD H ATC H PL ATFORM T ELESCOPIC STAB IL ISER GUARD RA IL BRACE PANEL Page 3... -
Page 5: Know Your Mitower+'S Components
KNOW YOUR MI TOWER+ COMPONENTS Claw 1 GUARDRAIL BRACE PANEL Claws are fitted to the guardrail brace panels and each has an automatic locking jaw which is released by simply moving the jaw’s trigger. The claw must only be attached to the frame with the opening facing outward. Attachment with the jaw’s opening facing inward will not fully protect the user if lent upon and may cause serious injury or death. - Page 6 Ensure all safety decals are present, intact and readable. A detailed Inspection Guide is available. To obtain a copy of this guide, please contact POP UP Products. Threads, hinges and brace claws may be lubricated with light oil to ensure correct functionality is maintained. Ensure oil does not contaminate climbing or walking surfaces.
-
Page 7: Know Your Kit List And Specifications
KNOW YOUR KIT LIST AND SPECIFICATIONS COMPONENT MATRIX AND WEIGHTS COMPONENT Weight (Unit) 4 RUNG FRAME 3.55 TELESCOPIC OUTRIGGER 4.35 HATCH PLATFORM 12.20 GUARDRAIL BRACE PANEL 4.15 220MM ADJUSTABLE LEG 0.85 125MM LOCKING CASTOR 2.45 TOE BOARD SET 6.50 MI TOWER+ WEIGHT (KG) 164.90 87.20 114.80... -
Page 8: Know Your Storage And Transport Pack
KNOW Y OUR STORAGE AN D TRANSPORT PACK TRANSPORT AND STORAGE TROLLEY COMPONENTS For ease of storage and of transportation, GUARDRAIL BRACE PANEL X2 MI TOWER+ has been designed so that all TOE BO ARD SET components can be safely stored within the HATCH PLAT FORM ADJUSTABLE LEG AND CASTOR X4 tower’s base assembly. -
Page 9: Safety Dos And Don'ts - Always
SAFETY DOS AND DON’TS - ALWAYS Always read and understand this guide before you begin assembly. Always ensure that all safety requirements are met and that MI TOWER+ is the correct access solution for the task you wish to perform. Always ensure that MI TOWER+ is assembled and dismantled by a qualified, competent person. -
Page 10: Safety Dos And Don'ts - Never
SAFETY DOS AND DON’TS - NEVER Never use MI TOWER+ if you don’t understand something in this guide; please contact the supplier for advice. Never assemble, use, move or dismantle MI TOWER+ if you are tired or unwell or if you are under the influence of alcohol or drugs. -
Page 11: Before You Start
BEFORE YOU START PREPARATION The floor area must be clear of any obstructions including materials and debris. Check that you have all the components necessary to construct the tower height you require. Check also each component for condition and correct function. If any part is missing or damaged/not working correctly it must be replaced before assembling. Assess the height of tower required before attempting assembly. -
Page 12: Getting Started
GETTING STARTED GETTING STARTED MI TOWER+ requires only one person to assemble and dismantle it. Your MI TOWER is supplied with uniform 1m high rung frames which can be used at any stage of the assembly. MIN. During erection, the frames may be connected together to create 2m high frames which makes assembly both quicker and easier. -
Page 13: Mitower+ 2M - Assembly
MI TOWER+ 2m - ASSEMBLY STEP 1 FROM TROLLEY For ease of storage and transportation your MI TOWER+ is designed so that all the components can be safely stored within the tower’s base. Start by removing the free-standing components from within the trolley and stack safely nearby for use. - Page 14 MI TOWER+ 2m - ASSEMBLY STEP 5 Stand inside the tower and fit a platform on to the eighth rung, making sure that the wind-lock catches engage. STEP 6 Fit a stabiliser to each corner of the tower. Position the lower horizontal stabiliser coupling clamp just above the frame’s second rung, then secure the top stabiliser coupling clamp just above the frame’s fifth rung.
-
Page 15: Mitower+ 3M - Assembly
MI TOWER+ 3m - ASSEMBLY STEP 1 REPLICATE STEPS 1 FROM 2M BUILD. Attach a guardrail brace panel to the vertical tube of one frame with the lower claw positioned above the first rung and the claws facing outward. Make sure the claws are correctly locked on to the frame tube. - Page 16 MI TOWER+ 3m - ASSEMBLY STEP 5 Place a set of conjoined frames one at each end of the tower ready to be fitted. Extend and lock the four component hangers located on either side of the first platform. Place a guardrail brace panel on to a component hanger on one side of the platform and a second platform on the other side.
-
Page 17: Mitower+ 4M - Assembly
MI TOWER+ 4m - ASSEMBLY STEP 1 REPLICATE STEPS 1 TO 7 FROM 2M BUILD. STEP 2 Extend and lock the four component hangers located on either side of the platform. From the ground place three guardrail brace panels onto the hangers on one side of the platform and two sets of conjoined four rung frames on the other side. - Page 18 MITOWER+ 4m - ASSEMBLY STEP 5 With both guardrail brace panels in position, you may access the platform. Unfold the toe board set and position so that it sits on the outer edge of the platform. Finally, retract all hangers and the tower is now complete and ready to use.
-
Page 19: Mitower+ 5M - Assembly
MI TOWER+ 5m - ASSEMBLY STEP 1 REPLICATE STEPS 1 TO 6 FROM 3M BUILD. Access the second platform and fit a set of conjoined frames to each end of the tower and apply the frame clips. Next, attach the guardrail brace panel with its lower jaw positioned above the seventeenth frame rung. - Page 20 MI TOWER+ 5m - ASSEMBLY STEP 4 With both guardrail brace panels in position, you may access the platform. Unfold the toe board set and position so that they sit on to the outer edge of the platform. Finally, retract all hangers and the tower is now complete and ready to use.
-
Page 21: Mitower+ 6M - Assembly
MI TOWER+ 6m - ASSEMBLY STEP 1 REPLICATE STEPS 1 TO 6 FROM 4M BUILD. Descend the tower and from the ground place three guardrail brace panels onto the hangers on one side of the first platform and two of conjoined four rung frames on the other side. Access the first platform and move the three guardrail brace panels from the hangers on the first platform on to the hangers of the second platform. - Page 22 MI TOWER+ 6m - ASSEMBLY STEP 3 Access the tower until you are half way through the third platform’s trap door. Now manoeuvre yourself so that you are sitting on the platform, with your legs through the trap door and your feet on the frame rungs.
-
Page 23: 10 Point Pre-Use Safety Checklist
10 POINT PRE-USE SAFETY CHECKLIST 10 POINT PRE-USE CHECKLIST FOR USERS BEFORE USE Ensure tower is correct, complete and level. COMPONENTS Check all components are free from damage. CASTORS Ensure the brakes are locked. ENVIRONMENT No environmental changes have influenced the safe use of your tower. STABILISER COUPLER CLAMPS Check they are secure &... -
Page 24: Registrations
REGISTRATIONS EN 1004 ISO 9001 Class 3 Page 19... - Page 25 POP UP Products Unit E1, Tenth Avenue Deeside Industrial Park Deeside Flintshire CH5 2UA...
Need help?
Do you have a question about the MI TOWER + and is the answer not in the manual?
Questions and answers