Download Print this page

Sloan Stone ELRF-82000 Installation Instructions Manual

Electronic lavatory round front

Advertisement

Quick Links

Electronic Lavatory Round Front
One, Two, Three, and Four Station
ELRF-81000
Electronic Lavatory System
Important
Read this entire installation manual to ensure proper
installation. When finished with the installation, file this
manual with the owner or maintenance department.
Compliance and conformity to local codes and
ordinances is the responsibility of the installers.
Separate parts from packaging and make sure
all parts are accounted for before discarding any
packaging material. If any parts are missing, do not
begin installation until all parts are obtained.
Make sure that all water supply lines have been
flushed and completely turned off before starting the
installation. Debris in supply lines can cause valves to
malfunction.
Tools and Supplies Required for Installation
Electric drill for drilling anchor holes
Standard sockets, basin wrench, and open end wrench set for
installing anchoring fasteners and faucets
Pipe wrench for installing drain lines
Phillips and straight blade screwdrivers
Tubing cutter
Level
Carpenter's square
Prior to Installation
Adequate structural support in or behind the wall is required. Refer to the appropriate rough-in diagram for dry weight of sink.
All electrical wiring is to be installed in accordance with national/local codes and regulations. Electrical outlets should be recessed and
installed prior to installation.
All plumbing should be installed in accordance with applicable codes and regulations.
Before connecting flex hoses to supply stops, flush all water lines until water is clear.
Hot and cold water supply lines/tempered supply line and drain lines. Recommended to have Control Stops on water supply lines in
place prior to installation.
Limited Warranty
Unless otherwise noted, Sloan Valve Company warrants its Products to be made of first class materials, free from defects of material or
workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner
when properly installed and serviced, for a period of three years (1 year for SF Faucets, special finishes and PWT electronics and 30 days
on PWT software) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts
which prove to be thus defective if returned to Sloan Valve Company, at customer's cost, and this shall be the sole remedy available
under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or
organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale. This warranty
does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
10500 Seymour Ave Franklin Park, IL 60131 | Phone: +1.847.671.4300 / +1.800.982.5839 | Fax: +1.800.447.8329 |
ELRF-82000
Electronic Lavatory System
Copyright © 2018 Sloan. All rights reserved.
ELRF-83000
Electronic Lavatory System
Turn off electrical power to the electrical outlets, then
unplug units prior to installation. Electrical power MUST
remain off until installation is complete.
Installers hardware must be appropriate for wall
construction. Wall anchors and mounting fasteners MUST
have a minimum pull-out rating of 1,000 lbs for 3/8" hole.
For standard height mounting, DO NOT exceed the
recommended 34 inch distance from the top of the sink
deck to the finished floor. To meet ADA requirements
the sink deck cannot not exceed the 34 inch maximum
height dimension.
Wear all proper safety equipment prior to installation
Caulk gun
1/2" NPT hot/cold or tempered supply piping
1 1/2" NPT drain piping including p-trap
Adhesive: Loctite® PL Premium® FAST GRAB Polyurethane
Construction Adhesive, or equivalent
110 volt GFCI protected electrical outlet for 100-120 VAC
plug-in transformer
Screen filter(s) included with faucet(s)
Backing supplied by others to meet local codes
CAUTION:
Installation Instructions
Code No. 0816150
ELRF-84000
Electronic Lavatory System
Page: 1 of 17
Sloan.com
(03/2018)

Advertisement

loading
Need help?

Need help?

Do you have a question about the Stone ELRF-82000 and is the answer not in the manual?

Questions and answers

Summarization of Contents

ELRF-81000 One Station Installation Guide
ELRF-81000 Sink Location Planning
Determine wall location and requirements for the ELRF-81000 lavatory system.
ELRF-81000 Component Identification
List and identify the components included in the ELRF-81000 lavatory system package.
ELRF-81000 Rough-In Dimensions
Specifies rough-in measurements and requirements for the ELRF-81000 system installation.
ELRF-81000 Backing and Bracket Mounting
Instructions for installing backing and mounting support brackets for the ELRF-81000.
ELRF-81000 Faucet and Sink Assembly
Steps for installing faucets and the main sink deck for the ELRF-81000 system.
ELRF-82000 Two Station Installation Guide
ELRF-82000 Sink Location Planning
Determine wall location and requirements for the ELRF-82000 lavatory system.
ELRF-82000 Component Identification
List and identify the components included in the ELRF-82000 lavatory system package.
ELRF-82000 Rough-In Dimensions
Specifies rough-in measurements and requirements for the ELRF-82000 system installation.
ELRF-82000 Backing and Bracket Mounting
Instructions for installing backing and mounting support brackets for the ELRF-82000.
ELRF-82000 Faucet and Sink Assembly
Steps for installing faucets and the main sink deck for the ELRF-82000 system.
ELRF-83000 Three Station Installation Guide
ELRF-83000 Sink Location Planning
Determine wall location and requirements for the ELRF-83000 lavatory system.
ELRF-83000 Component Identification
List and identify the components included in the ELRF-83000 lavatory system package.
ELRF-83000 Rough-In Dimensions
Specifies rough-in measurements and requirements for the ELRF-83000 system installation.
ELRF-83000 Backing and Bracket Mounting
Instructions for installing backing and mounting support brackets for the ELRF-83000.
ELRF-83000 Faucet and Sink Assembly
Steps for installing faucets and the main sink deck for the ELRF-83000 system.
ELRF-84000 Four Station Installation Guide
ELRF-84000 Sink Location Planning
Determine wall location and requirements for the ELRF-84000 lavatory system.
ELRF-84000 Component Identification
List and identify the components included in the ELRF-84000 lavatory system package.
ELRF-84000 Rough-In Dimensions
Specifies rough-in measurements and requirements for the ELRF-84000 system installation.
ELRF-84000 Backing and Bracket Mounting
Instructions for installing backing and mounting support brackets for the ELRF-84000.
ELRF-84000 Faucet and Sink Assembly
Steps for installing faucets and the main sink deck for the ELRF-84000 system.