Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AERMEC HMI160T
Summarization of Contents
Safety Standards R32 Gas
R32 Gas Safety Standards
Detailed safety standards for R32 refrigerant gas, including warnings and precautions.
R32 Gas Advantages
Advantages of R32 gas, highlighting its environmental and thermodynamic benefits.
R32 Gas Maintenance and Repair Warnings
Specific warnings for maintenance and repair involving R32 gas.
R32 Refrigerant Gas Filling
Procedures and precautions for filling R32 refrigerant gas.
Refrigerant Gas Leak Detection
Methods for detecting refrigerant gas leaks.
General Warnings
General Unit Operation Instructions
Key safety instructions and risks associated with the unit's operation.
Residual Risk Precautions
General precautions to mitigate residual risks during installation and operation.
Safety Notices (Please Be Sure to Abide)
Product Disposal Information
Guidance on the proper disposal of the product according to EU regulations.
General Warnings
Read Owner's Manual Before Use
Advice to read the owner's manual before operating the appliance.
Receiving the Product
Product Identification Methods
Information on identifying Aermec products via labels and rating plates.
Handling and Transport
Inspection Upon Product Receipt
Procedures for checking the unit upon delivery for damage or missing parts.
Unit Lifting Procedures
Instructions and safety precautions for lifting the unit.
Unit Storage Recommendations
Recommendations for storing the unit if not immediately installed.
Description
Unit Type Description
Description of the HMI unit's type and intended use.
Unit Features and Components
Key features of the HMI unit, including hydraulic components and regulation.
Unit Operating Limits
Specifies the operational limits for cooling and heating modes.
Operating Limits
Cooling Mode Operating Limits
Graphical representation of operating limits for cooling mode.
Heating Mode Operating Range
Graphical representation of operating limits for heating mode.
Compressor Restraint Removal
Foot Bracket Removal Procedure
Step-by-step guide for removing foot brackets.
Hydraulic Connections
Hydraulic Connections and System Preparation
Detailed instructions for making hydraulic connections and system preparation.
Heat Exchanger Freeze Prevention
Methods to prevent freezing in the heat exchanger during winter.
Anti-Freeze Solution Precautions
Precautions for using anti-freeze solutions in the hydraulic system.
Example of Installation
Installation Example 1: Floor System/Fancoil+DHW
A hydraulic diagram for a specific installation configuration.
Charging and Discharging of Refrigerant
Refrigerant Drainage Procedure
Steps for draining refrigerant from the unit.
Refrigerant Charging Procedure
Refrigerant Leak Detection Methods
Methods for detecting refrigerant leaks in systems with flammable refrigerants.
Electrical Wiring Guidelines
Power Wire and Leakage Switch Specifications
Recommended specifications for power cables and leakage switches.
Rubber Ring Usage Instructions
Instructions for using rubber rings for wire management.
Control Panel Connection
Control Panel Kit Components
Components included in the control panel kit.
Control Panel Dimensions
Dimensions of the control panel.
Wall Installation Dimensions
Dimensions for mounting the control panel on a wall.
Wiring Diagrams
HM1040-060-080 Wiring Diagram
Wiring diagrams for HM1040-060-080 models.
Terminal Board Layouts
Terminal Board HM1040-060-080
Layout and connections for terminal boards of HM1040-060-080 models.
Commissioning Warnings and Procedures
Unit Start-Up Procedures
Procedures for unit start-up, including checks with and without power.
Hydraulic Circuit Controls Checks
Checks for hydraulic circuit components and operation.
Final Commissioning Steps
Final steps for commissioning the unit after checks.
Machine Operation Checks
Checks to be performed while the machine is running.
Unit Maintenance Guidelines
Maintenance Safety Precautions
Safety precautions to be followed during maintenance operations.
Mechanical Risk Precautions During Maintenance
Specific precautions for mechanical risks during maintenance.
Chemical, Fire, Environmental Risk Prevention
Precautions related to chemical, fire, and environmental hazards.
Pressure and Temperature Risk Prevention
Precautions concerning pressure and temperature risks.
Electrical Risk Prevention
Precautions related to electrical risks.
Machine Cleaning Procedure
Machine Inspection and Control
Procedures for inspection and control of the machine.
Routine and Extraordinary Maintenance
Details on routine and extraordinary maintenance tasks.
Recommended Periodic Maintenance
Periodic Maintenance Interventions Schedule
General interventions and their recommended frequencies.
Cooling Circuit Maintenance (Full Load)
Maintenance tasks for the cooling circuit during full load operation.
Compressor Control Maintenance
Maintenance checks related to compressor control.
Hydraulic Circuit Controls Maintenance
Maintenance checks for hydraulic circuit components.
Centrifugal Compressor Maintenance
Decommissioning and Component Disposal
Procedures for decommissioning and disposing of unit components.
Need help?
Do you have a question about the HMI160T and is the answer not in the manual?
Questions and answers