Related Manuals for Rohde & Schwarz R&S FSH13
Summarization of Contents
1 Putting into Operation
Front view
Identifies physical connectors and controls on the front panel of the spectrum analyzer.
Unpacking the Instrument
Guides the user through the process of unpacking the R&S FSH and its accessories.
Setting up the Instrument
Describes how to position and set up the R&S FSH for optimal viewing and operation.
Switching on the Spectrum Analyzer
Details the procedure for powering on the R&S FSH using the power supply or battery.
Spectrum Analyzer Connectors
Lists and describes all the connectors available on the R&S FSH for various inputs and outputs.
Tracking generator output
Explains how to connect and use the tracking generator output for measurements.
Screen Settings
Covers adjusting screen brightness, contrast, and color for optimal readability.
Country-Specific Settings
Guides users on setting language, date format, and length units for international use.
Setting the Date and Time
Details how to set the internal clock and date for accurate time-stamping of measurements.
Charging the Battery
Provides instructions on how to charge the internal battery of the R&S FSH.
Selecting the Instrument Default Setup
Explains how to set the R&S FSH to its default configuration or a user-defined setup.
External Reference / External Trigger Switchover
Describes how to switch between external trigger and external reference inputs.
Controlling the RF Attenuator
Explains how to select RF attenuator modes for optimal sensitivity or distortion.
Using a Preamplifier
Details how to enable the internal preamplifier to increase measurement sensitivity.
PIN Entry
Covers setting up and managing the Personal Identification Number (PIN) for instrument security.
Connecting a Printer
Guides on connecting printers for outputting screenshots and measurement data.
Setting the Baud Rate for Remote Control
Explains how to set the baud rate for remote control of the R&S FSH.
Enabling Options
Describes how to enable optional features using key codes.
Checking the Installed Options
Shows how to check which optional features are installed on the R&S FSH.
2 Getting Started
Measurements on CW Signals
Introduces basic spectrum analyzer measurements using continuous wave (CW) signals.
Setting the Reference Level
Explains how to set the reference level for optimal dynamic range in measurements.
Frequency Measurements
Details how to perform frequency measurements and use markers for accuracy.
Harmonic Measurements of a Sinewave Signal
Guides on measuring harmonic levels and ratios of sinewave signals.
Power Measurements Using the Power Sensor
Describes how to perform accurate power measurements using external power sensors.
Power and Return Loss Measurements with the R&S FSH-Z14 or the R&S FSH-Z44
Explains power and return loss measurements using directional power sensors.
Two Port Transmission Measurements
Details how to measure gain or attenuation of two-port devices using the tracking generator.
Measurement of Return Loss
Guides on performing return loss measurements using a VSWR bridge.
Performing Distance To Fault Measurements
Explains how to perform distance-to-fault measurements on cables.
Calibrating the test setup
Details the procedure for calibrating the test setup for accurate measurements.
Operation in Receiver Mode
Switching on the receiver mode
Describes how to activate the receiver mode for specific frequency measurements.
Setting the frequency
Guides on setting the operating frequency in receiver mode.
Selecting the frequency step size
Explains how to adjust the frequency step size for receiver mode.
Tuning the frequency in channel grids
Details tuning the receiver by selecting predefined channel tables.
Direct entry of a channel table
Guides on manually defining channel parameters for receiver mode.
Selecting the reference level
Explains how to set the reference level for receiver measurements.
Selecting the bandwidth
Details how to select the appropriate bandwidth for receiver measurements.
Setting the detector
Guides on choosing the detector type (peak, average, RMS) for receiver measurements.
Setting the measurement time
Explains how to set the measurement time for collecting receiver data.
Scanning in the receiver mode
Describes how to scan across frequencies and display measurement levels.
Measuring the Carrier-to-Noise Ratio
Determining the carrier power (reference power or reference level)
Explains how to determine the reference carrier power for C/N calculations.
Manual entry of a reference power or a reference level
Guides on manually entering reference power or level for C/N calculation.
Activating the C/N measurement
Details the procedure for activating the carrier-to-noise measurement mode.
Selecting the reference measurement
Guides on selecting the method to determine the reference carrier power.
Selecting the reference channel
Explains how to select the reference channel for C/N measurements.
Entering the channel bandwidth of the reference channel
Details how to specify the channel bandwidth for the reference measurement.
Selecting the reference unit
Guides on selecting the unit (dBm, dBmV, dBμV) for reference measurement results.
Manual reference entry
Describes how to manually enter the reference power or level.
Measuring the noise power
Explains how to measure noise power in an unoccupied transmission channel.
Selecting the result display
Guides on selecting the desired result display format (C/N or C/No).
Saving and Recalling Settings and Test Results
Saving Measurement Results
Details how to save measurement results and instrument settings to internal memory.
Saving Calibration Data
Explains how to save calibration data along with settings and results.
Recalling Measurement Results
Guides on reviewing previously saved measurement results and settings.
Printing Out Measurement Results
Printer with serial interface
Describes connecting a printer via a serial interface.
Printer with parallel interface
Guides on connecting a printer using a serial/parallel converter.
Operating the R&S FSH
Explains the process of printing a screenshot to a connected printer.
Need help?
Do you have a question about the R&S FSH13 and is the answer not in the manual?
Questions and answers