Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Echo ES-210 - SERIAL NUMBER 07001001-07999999
Summary of Contents for Echo ES-210 - SERIAL NUMBER 07001001-07999999
- Page 1 SHRED 'N' VAC Operator's Manual MODEL ES-210 Serial Number 07001001 - 07999999 WARNING DANGER Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood for proper and safe operation. X7531131700 X753000920 03/03...
-
Page 2: Table Of Contents
NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages. -
Page 3: Manual Safety Symbols And Important Information
If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. P/N 89016006361... -
Page 4: International Symbols
Proper clothing and safety gear must be worn when operating SHRED 'N' VAC®. Physical Condition Hearing Protection Your judgment and physical dexterity may not be good: ECHO recommends wearing hearing protection whenever • if you are tired or sick, unit is used. • if you are taking medication, •... -
Page 5: Extended Operation/Extreme Conditions
® 'N' V HRED PERATOR ANUAL EXTENDED OPERATION EXTREME CONDITIONS Vibration and Cold To reduce the risk of RSI/CTS, do the It is believed that a condition called Raynaud’s Phenomenon, which following: affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. -
Page 6: Safe Operation
SAFE OPERATION Keep A Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do Determine Operation Area not work in odd positions or on ladders. • Do not perform Maintenance or Assembly procedures with engine running. -
Page 7: Description
1 - Elbow Pipe 1 - Debris Bag 1 - Operator's Manual 1 - Warranty Registration Card 1 - ECHO Emissions and Warranty Statement 1 - T-Wrench 1 - Echo Power Blend 2-stroke oil sample 1. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop. -
Page 8: Specifications
15. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank, priming the carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. -
Page 9: Assembly
® 'N' V HRED PERATOR ANUAL SSEMBLY WARNING DANGER Never perform maintenance or assembly procedures with engine running, or serious personal injury may result. BLOWER APPLICATION Install Blower Pipes 1. Align grooves in straight pipe with pegs on blower housing and slide pipe onto housing. -
Page 10: Vacuum/Shredding Application
5. Align grooves in discharge elbow with pegs on blower, and slide elbow (D) on to blower. Turn elbow counterclockwise to lock in place. Elbow must angle back toward operator position as shown. 6. Place debris bag opening over flared end of elbow, and cinch bag (E) securely with Velcro strap. -
Page 11: Pre-Operation
• Move at least 3 m (10 ft.) from refueling dards. Engine problems due to inadequate lubrication caused by location before starting. failure to use an ISO-L-EGD and J.A.S.O. FC certified oil, such as Echo premium Power Blend , will void the two-stroke engine warranty. -
Page 12: Operation
PERATION • Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Before starting the unit, equip yourself and any other person working within the 15 m (50 ft.) Safety Zone with the required Protective Equipment and clothing. -
Page 13: Starting Warm Engine
Move stop switch (A) to "STOP" position. WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using blower again. -
Page 14: Blower Operation
BLOWER OPERATION WARNING DANGER Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may result. . Do not point the blower pipe in the direction of people or pets. Never operate unit without either housing cover grill or vacuum tube installed on unit securely, otherwise bodily harm may result. -
Page 15: Shred 'N' Vac ® Operation
® 'N' V HRED PERATOR ANUAL ® SHRED OPERATION WARNING DANGER Flying debris hazard. Never operate unit as a vacuum unless discharge elbow is installed and debris bag is securely cinched to elbow. Failure to follow instructions can result in serious injuries. 1. -
Page 16: Maintenance
ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs. -
Page 17: Air Filter
® 'N' V HRED PERATOR ANUAL AIR FILTER Level 1. Tools required: 25-50 mm (1-2 in.) medium bristle brush. Parts required: 90008 REPOWER Air and Filter Kit NOTE Clean daily. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. -
Page 18: Spark Plug
SPARK PLUG Level 2. Tools required: 3/4 in. Spark Plug deep socket, Feeler gauge (preferably a wire gauge), Parts Required: Spark Plug, NGK BPMR-8Y 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. -
Page 19: Exhaust System
® 'N' V HRED PERATOR ANUAL Cleaning Cylinder Fins 1. Remove spark lead and spark plug. 2. Remove four 3 mm hex screws, side handle and recoil starter. 3. Remove engine cover (five screws), pull cover away from engine. Loosely install spark plug to prevent dirt from entering cylinder. Clean cylinder fins to allow cooling air to pass freely. -
Page 20: Shredder Blade
The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. ECHO strongly recommends that you return your unit to your ECHO dealer for this important maintenance service. SHREDDER BLADE Level 1. -
Page 21: Carburetor Adjustment
Accelerate to full throttle to check for smooth transition from idle to full throttle. If engine stops or stalls after full warm up, return the unit to your authorized ECHO dealer for repair. 6. Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed RPM should be set to specifications found on page 8 "Specifica-... -
Page 22: Troubleshooting
ROUBLESHOOTING r o t r o t i a r i l l r o t r e l i l y i l y r o t r e l f f u r e l h t i r u t r / n r i a... -
Page 23: Storage
2. Place the stop switch in the "STOP" position. 7. Remove the spark plug and pour 7cc (1/4 oz.) of fresh, clean ECHO 2-stroke engine oil into the 3. Remove accumulation of grease, oil, dirt and debris cylinder through the spark plug hole. -
Page 24: Servicing Information
• Purchasing from your Echo Dealer. • Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO, INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address above.
Need help?
Do you have a question about the ES-210 - SERIAL NUMBER 07001001-07999999 and is the answer not in the manual?
Questions and answers