Related Manuals for American Audio VLP - REV 9-10
Summary of Contents for American Audio VLP - REV 9-10
-
Page 1: User Instructions
Professional Power Amplifier VLP Series AmericAn Audio ® User Instructions 6122 S. eastern Ave. Los Angeles ca. 90040 rev. 9/10... - Page 2 Fachpersonal durchführen lassen. aChtUng: um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte diesen Gerät nicht dem regen oder Feuchtigkeit ausgesetz werden. vor inbetriebnahme unbedingt die Bedienungsanleitung lesen. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 2...
-
Page 3: Table Of Contents
Front Panels.........................................5 rear Panels........................................7 inputs...........................................9 outputs..........................................9 Speakon output connector Assembly...............................11 operating modes......................................12 Protection circuitry Limiter.........................................13 Short circuit Protection...................................13 Thermal Protection..................................14 Amplifier Features.......................................14 Speaker Setup......................................15 Warranty.........................................16 Specifications.......................................17 ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 3... -
Page 4: Safety Precautions
The appliance has been exposed to rain or water. Fax: (323) 582-2610 d. The fixture does not appear to operate normally or exhibits a marked change in performance. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 4... -
Page 5: Front Panel
8. Channel 2 Clip Indicator - This red Led will begin to flash when channel one begins to overload (clip). At this point channel one will be- gin to distort. under heavy clipping activity lower the channel one gain ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 5... - Page 6 (clip). At this point channel one will be- gin to distort. under heavy clipping activity lower the channel one gain control to reduce the risk of damage to your speakers and amplifier. This ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 6...
-
Page 7: Rear Panels
Always be sure to replace the fuse with an exact match as the one being replaced, unless otherwise told to do so by an authorized American Au- dio® service technician. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 7... - Page 8 Black is negative signal. 47. Channel 1 output Jack/5 way Binding Post - connect to your speaker’s input jack. red is positive signal and Black is negative signal. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 8...
-
Page 9: Inputs
©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 9... - Page 10 You can purchase the Speakon nL4Fc connectors from your local audio dealer. ® ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 10...
-
Page 11: Speakon Output Connector Assembly
INPUT T U CAUTION SPEAKON 1+ HOT MINIMUM LOAD IMPEDANCE 2 OHM PERCHANNEL 4 OHM BRIDGE 1 COLD - B ID E + UTPUTS 120 60 4800 A TTS ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 11... -
Page 12: Operating Modes
To run in parallel mono mode connect your system as you would if you were going to run in stereo mode. Then flip the mode switch to “mono.” Be sure the amp is off or the power is disconnected before making any changes. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 12... -
Page 13: Limiter
"clip" Led and “Protect" Led will light simultaneously indicating amplifier fault. All channel output during the “Short circuit Protection" will be interrupted (i.e. no sound out ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 13... -
Page 14: Thermal Protection
Led IndICatorS - each channel has five LedS. Two Leds indicate signal level activity; two green Leds. one yellow Led indicates signal clipping. one red Led indicates protections mode for shorts/ overload. one blue Led indicates power for each individual chan- nel. ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 14... -
Page 15: Speaker Setup
Mono brIDge set-Up use channel 1 inputs only (XLr or 1/4” Jacks) Figure 16 use the two positive binding post termainals (red) for speaker output. speaKers 8 oHm minimum ©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 15... -
Page 16: Warranty
This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American Audio® con- cludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American Audio®... -
Page 17: Specifications
14” x 19” x 3.5” 14” x 19” x 3.5” (LxWxH): 336 x 482 x 44mm 360 x 482 x 88mm 360 x 482 x 88mm Weight: 24lbs/11Kgs 33lbs/15Kgs 42lbs/19Kgs American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 17... - Page 18 ©American Audio® World Headquarters: 6122 S. eastern Ave. Los Angeles, cA 90040 uSA Tel: 323-582-3322 Fax: 323-725-6100 Web: www.AmericanAudio.us e-mail: info@americanaudio.us American dJ europe Junostraat 2 6468 eW Kerkrade netherlands service@americandj.eu / www.americandj.eu Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99...