Related Manuals for SOLZAIMA Hidro 23
Summarization of Contents
Package Content and Unpacking
1.1. Unpacking the Unit
Instructions on how to unpack the free-standing fire unit from its packaging.
Safety Precautions and Recommendations
2.1. Safety Recommendations
Key safety recommendations for operating the free-standing pellet fire unit.
Installing the Pellet Fire
5.1. Installation Requirements
Specifies minimum distances and base requirements for safe installation of the unit.
5.2. Duct and Fume Extraction Systems
Details requirements for exhaust pipes and fume extraction systems.
5.3. Installation Without a Chimney
Explains the process for installing the unit without a chimney.
5.4. Installation With a Chimney
Describes how to install the unit with a chimney connection.
Hydraulic Installation and Operation Modes
6.1. Operating Mode for Radiator/Buffer Tank
Guidance on configuring the unit's operating mode for radiator or buffer tank systems.
Remote Control Operations
9.1. Remote Control and Display
Overview of the remote control interface and display functions.
9.1.1. Menu Navigation
Explains the display menu for operation modes and temperature settings.
9.1.2. Water Temperature Settings
How to set and adjust the water temperature for heating.
9.1.3. Date and Time Settings
Guide for setting the unit's date and time parameters.
9.1.4. Timer Configuration
Instructions on setting up the timer for automatic operation.
9.1.5. Sleep Timer Setup
How to set a sleep timer to turn off the unit at a specific time.
9.1.6. Information Menu
Information on accessing unit software codes and firmware versions.
9.1.7. Settings Menu Options
How to access and modify unit settings like language and eco mode.
9.1.8. Technical Menu Access
Accessing the technical menu requires a password for advanced adjustments.
Columbus Control System
11.1. Display Overview
Describes the information shown on the Columbus control display.
11.2. Settings Menu
Accessing menus for unit configuration and customization.
11.2.1. Language Selection
How to select the desired language for the unit's interface.
11.2.2. Time and Date Configuration
Guide for setting the correct time and date on the unit.
11.2.3. Summer-Winter Mode
Functionality for summer/winter mode, noted as not applicable.
11.3. Display Menu Options
Options for adjusting display settings like contrast and brightness.
11.3.1. Contrast Adjustment
Adjusting screen contrast from 0 to 30.
11.3.2. Minimum Brightness Setting
Adjusting screen brightness from 0 to 20.
11.3.3. Screen Saver Function
Activating or deactivating the screen lock feature.
11.3.4. Firmware Codes Information
Viewing communication address, control board type, and firmware version.
11.4. Service Menu Access
Accessing advanced service functions for calibration and diagnostics.
11.4.1. Counters and Usage Data
Viewing working hours, ignition counts, and failed ignitions.
11.4.2. Error List Display
Displaying the last 10 recorded errors with timestamps.
11.4.3. Secondary Information Check
Checking product code, fan status, auger, and heating fan status.
11.4.4. Cleaning Reset Function
Function to reset the cleaning cycle indicator.
11.4.5. Auger Calibration Procedure
Adjusting the pellet feeding quantity.
11.4.6. Fan Calibration Procedure
Adjusting the fan speed for optimal operation.
11.4.7. Automatic Power Setting
Setting combustion power in automatic mode.
11.4.8. Manual Load Activation
Activating manual pellet loading function.
11.5. Power Menu Options
Menu to adjust combustion power levels.
11.5.1. Pellet Power Adjustment
Modifying the system's combustion power.
11.6. Thermostats Menu
Adjusting boiler thermostat values.
11.7. Chrono Menu Setup
Setting up the time scheduler for automatic on/off cycles.
11.8. Info Menu Content
Viewing measured values and information related to the unit's electronics.
Operating the Unit
13.1. Stopping the Unit
Procedure for stopping the unit's operation sequence.
13.2. Turning Off the Unit
Steps to safely disconnect the unit from the mains.
Installing the Casings
14.1. Casings Installation for Hidro 12
Step-by-step guide to install casings on the Hidro 12 model.
14.2. Casings Installation for Hidro 17 and Hidro 23
Guide for installing casings on Hidro 17 and Hidro 23 models.
14.3. Pellet Reservoir Lid Operation
How to open and close the pellet reservoir lid.
14.4. Filling the Pellet Reservoir
Instructions for refilling the pellet reservoir.
Remote Control Installation and Operation
15.1. Remote Control Assembly Instructions
Steps for assembling and connecting a remote control or chrono-thermostat.
Maintenance Procedures
16.1. Daily Maintenance
Routine tasks for maintaining the pellet fire unit, focusing on ash removal.
16.2. Weekly Maintenance
Procedures for weekly cleaning of airflow pipes and internal components.
16.3. Additional Cleaning
Specific cleaning tasks for higher pellet consumption intervals.
16.4. Cleaning the Glass
Proper method for cleaning the unit's glass door.
Electrical Diagrams
20.1. Diagram (Not Columbus Electronics)
Electrical diagrams for units without Columbus electronics.
20.2. Diagram (Columbus Electronics)
Electrical diagrams for units with Columbus electronics.
Hydraulic Pumps Information
21.1. Pump UPM3 FLEX AS 15-70 130mm
Technical details and performance graph for the UPM3 FLEX circulating pump.
21.2. Pump Wilo 15-130/7-50 Details
Description and components of the Wilo 15-130/7 50 circulator pump.
Warranty Information
24.1. Model-Specific Warranty Conditions
Conditions for activating the warranty, including mandatory start-up service.
24.2. General Warranty Conditions
General terms and conditions governing product warranty.
Annexes
25.1. Timer Weekly Programming
Weekly programming schedules for the timer function.
25.2. Flow Chart Hidro 12
Flowchart illustrating the lighting process for the Hidro 12 model.
25.3. Flow Chart Hidro 17 and Hidro 23
Flowcharts for the lighting process of Hidro 17 and Hidro 23 models.
25.4. Statement of Performance
Declaration of performance for the product according to harmonized standards.
Need help?
Do you have a question about the Hidro 23 and is the answer not in the manual?
Questions and answers