PIKE 1064E 規格列表 控制器 LSISAS1064E 接口 華碩 PIKE 接口 端口數量 4 端口 支持設備 SAS 與 SATA II 設備 數據傳輸率 SATA II and SAS 3 Gb/s per PHY RAID 級別 RAID0/RAID1/RAID1E 支持操作系統* Windows ® Server 2003/2000/XP/Vista Red Hat ® Enterprise Linux 3/4/5 SUSE Linux Enterprise Server 8/9/10 LSI MegaRAID Storage Manager (MSM) 用於...
IM 功能支持熱插拔,所以,當一組 IM 卷的硬盤失效時,您可以輕鬆恢復 卷,而插拔後的硬盤會自動重新鏡像。 請依照以下步驟創建一個 IM 卷: 1. 安裝完 SAS 硬盤後啟動系統。 2. 在 POST過程中,請按下 <Ctrl+C> 進入 SAS 設置程序。 LSI Corporation MPT SAS BIOS MPTBIOS-6.20.00.00 (2007.12.04) Copyright 2000-2007 LSI Corporation. Press Ctrl-C to start LSI Corp Configuration Utility... 為防止數據丟失,創建過程中請不要關閉系統。 華碩 PIKE 1064E...
Page 14
3. 以下畫面出現。選擇一個通道並按下 <Enter> 來進入設置程序。 LSI Corp Config Utility v6.20.00.00 (2007.12.04) Adapter List Global Properties Adapter FW Revision Status Boot Slot Order SAS1064E 1.24.00.00-IR Enabled Esc = Exit Menu F1/Shift+1 = Help Alt+N = Global Properties -/+ = Alter Boot Order Ins/Del = Alter Boot List 通道數量取決於控制器。...
Page 15
Esc = Exit Menu F1/Shift+1 = Help SPACE/+/- = Select disk for array or hot spare C = Create array 默認情況下,在陣列創建之前,RAID Disk 欄位顯示為 No。在 以下几種情況下,此欄位為灰色無法設置: • 硬盤不符合 RAID 陣列的最低要求。 • 硬盤容量較小,無法鏡像第一塊硬盤中的已有數據。 • 硬盤已被指定為 RAID 陣列的 Hot Spare。 • 硬盤已是另一陣列的一部分。 華碩 PIKE 1064E...
Page 16
7. 確認信息出現。 按下 <M> 保留第一塊硬盤上的已有數據。若您選擇此項,第一塊硬盤數 據將被鏡像到您稍後會添加到卷中的第二塊硬盤。請確認您想要鏡像的 數據位於第一塊硬盤內。 按下 <D> 覆蓋所有數據並創建新的 IM 陣列。 LSI Corp Config Utility v6.20.00.00 (2007.12.04) Create New Array -- SAS1064E M - Keep existing data, migrate to an IM array. Synchronization of disk will occur. D - Overwrite existing data, create a new IM array. ALL DATA on ALL disk in the array will be DELETED!! No Synchronization performed.
35003 SEAGATE ST336754SS 0003 [Yes] [No] ------- ---- 35003 SEAGATE ST336754SS 0003 [Yes] [No] ------- ---- 35003 Esc = Exit Menu F1/Shift+1 = Help SPACE/+/- = Select disk for array or hot spare C = Create array 華碩 PIKE 1064E...
Page 18
默認情況下,在陣列創建之前,RAID Disk 欄位顯示為 No。在 以下几種情況下,此欄位為灰色無法設置: • 硬盤不符合 RAID 陣列的最低要求。 • 硬盤容量較小,無法鏡像第一塊硬盤中的已有數據。 • 硬盤已被指定為 RAID 陣列的 Hot Spare。 • 硬盤已是另一陣列的一部分。 4. 重複步驟 3 添加其他硬盤到卷。 5. 完成後,按下 <C> 創建陣列,然後選擇 Save changes then exit this menu。 Create and save new array? Cancel Exit Save changes then exit this menu Discard changes then exit this menu Exit the Configuration Utility and Reboot...
35003 SEAGATE ST336754SS 0003 [Yes] [No] ------- ---- 35003 SEAGATE ST336754SS 0003 [Yes] [No] ------- ---- 35003 Esc = Exit Menu F1/Shift+1 = Help SPACE/+/- = Select disk for array or hot spare C = Create array 華碩 PIKE 1064E...
Page 20
默認情況下,在陣列創建之前,RAID Disk 欄位顯示為 No。在 以下几種情況下,此欄位為灰色無法設置: • 硬盤不符合 RAID 陣列的最低要求。 • 硬盤容量較小,無法鏡像第一塊硬盤中的已有數據。 • 硬盤已被指定為 RAID 陣列的 Hot Spare。 • 硬盤已是另一陣列的一部分。 4. 重複步驟 3 添加其他硬盤到卷。 5. 完成後,按下 <C> 創建陣列,然後選擇 Save changes then exit this menu。 Create and save new array? Cancel Exit Save changes then exit this menu Discard changes then exit this menu Exit the Configuration Utility and Reboot...
ALL DATA on array disks will be DELETED! Create IS Volume Create Integrated Striping array of 2 to 10 disks. ALL DATA on array disks will be DELETED! Esc = Exit Menu F1/Shift+1 = Help Enter = Choose array type to create 2-11 華碩 PIKE 1064E...
Page 22
3. View Array 畫面出現。這裡您可以查看已創建的 RAID 陣列的屬性。若 您設置了 hot spare,它也將被列出。若您創建了不止一組陣列,您可 以按下 <Alt+N> 查看下一組陣列。 LSI Corp Config Utility v6.20.00.00 (2007.12.04) View Array -- SAS1064E Array 1 of 1 Identifier LSILOGICLogical Volume 3000 Type Scan Order Size(MB) 51498 Status Optimal Manage Array Slot Device Identifier RAID Drive...
Page 23
(2007.12.04) Manage Array -- SAS1064E Identifier LSILOGICLogical Volume 3000 Type Scan Order Size(MB) 51498 Status Optimal Manage Hot Spares Synnchronize Array Activate Array Delete Array Esc = Exit Menu F1/Shift+1 = Help Enter = Select Item 2-13 華碩 PIKE 1064E...
Page 24
4. 使用方向鍵選擇您想要設置為 hot spare 的硬盤,然後將光標移至 Hot Spr 列,按下 <+>, <-> 或空格鍵。Drive Status 列將顯示 Hot Spare。 按下 <C> 確認更改。 LSI Corp Config Utility v6.20.00.00 (2007.12.04) Manage Hot Spare -- SAS1064E Identifier LSILOGICLogical Volume 3000 Type Scan Order Size(MB) 51498 Status Optimal Slot Device Identifier Drive...
Page 25
LSILOGICLogical Volume 3000 Type Scan Order Size(MB) 34332 Status Optimal Manage Hot Spare Synnchronize Array Activate Array Delete Array Esc = Exit Menu F1/Shift+1 = Help Enter = Select Item 2. 按下 <Y> 刪除,或按下 <N> 取消操作。 2-15 華碩 PIKE 1064E...
設置畫面。 4. 將電腦重新開機。 5. 當出現從 CD 開機的畫面時,請按下任一鍵。 Loading FreeDOS FAT KERNEL GO! Press any key to boot from CDROM... 6. Makedisk 菜單出現。選擇 PIKE 1064E SAS Driver,並按下 <Enter> 進 入子菜單。 Create Driver Diskette Menu PIKE 1064E SAS Driver FreeDOS command prompt...
Page 33
7. 用方向鍵選擇您想要創建的 RAID 驅動程序軟盤的類型。 PIKE 1064E SAS card Driver Windows 2000 Server SP4 Windows XP 32 bit Windows XP 64 bit Windows Server 2003 32 bit Windows Server 2003 64 bit Windows Vista 32 bit Windows Vista 64 bit Windows Server 2008 32 bit...
® 3.1.2 Windows Server 2003 操作系統 ® 在 Windows Server 2003 操作系統安裝過程中 ® 請依照以下步驟在 Windows Server 2003 操作系統安裝過程中安裝 RAID 卡驅動程序: ® 1. 用 Windows Server 2003 操作系統安裝光盤啟動系統。然後就會進入 Windows 2003 Setup 安裝畫面。 2. 當出現“Press F6 if you need to install a third party SCSI or RAID driver...”的信息時,請按下...
Page 35
Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen. LSI Fusion-MPT SAS Driver (Server 2003 32-bit) ENTER=Select F3=Exit 6. Windows Server 2003 安裝程序會開始從 RAID 驅動程序軟盤中載入 RAID 控制驅動程序,當完成後,請按 <Enter> 鍵繼續其他的安裝。 7. 完成 RAID 驅動程序安裝後,操作系統會繼續進行安裝,請依照畫面的指 示來進行。 華碩 PIKE 1064E...
Page 36
® 在 Windows Server 2003 操作系統安裝後 請依照以下步驟在 Windows ® Server 2003 操作系統安裝後更新 RAID 卡 驅動程序: 1. 使用鼠標按右鍵選擇桌面上的 My Computer(我的電腦)圖標,然後從 彈出的菜單中,選擇 Properties(屬性)。 2. 接著請點擊 Hardware(硬件)這欄,然後點擊 Drvice Manager(設備管 理器)來顯示系統目前連接的相關硬件。 3. 雙擊 LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort 項 目。 4.
Page 37
5. 點選 Install from a list or specific location (Advanced),然後點擊 Next 繼續。 6. 點選 Don’t search. I will choose the driver to install,然後點擊 Next 繼 續。 7. 在軟驅中放入剛剛您所製作的 RAID 驅動程序軟盤。 8. 選擇 LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort,然 後點擊 Have Disk。 華碩 PIKE 1064E...
Do you have a driver disk? 4. 當詢問您來源的驅動程序軟盤安裝位置時,請按下 <Tab> 鍵來選擇 fd0。 接著再按 <Tab> 鍵來移至 OK 處,然後按下 <Enter> 鍵。 Driver Disk Source You have multiple devices which could serve as sources for a driver disk. Which would you like to use? scd0 Cancel 華碩 PIKE 1064E...
Page 40
5. 當出現此對話框時,請在軟驅中放入 Red Hat Enterprise 的 RAID 驅動 程序軟盤,並選擇 OK,然後按下 <Enter> 鍵。 Insert Driver Disk Insert your driver disk into /dev/fd0 and press “OK” to continue. Back 此時會開始安裝 RAID 驅動程序至系統中。 6. 當詢問您是否加載附加的 RAID 控制器驅動程序時,選擇 No,然後按 下 <Enter>。 More Driver Disks? Do you wish to load any more driver disks? 7.
Language 1280 x 1024 Driver 3. 按下 <F5>,然後從菜單中選擇 Yes。按下 <Enter>。 Boot from Hard Disk Installation Installation--ACPI Disabled Installation--Local APIC Disabled Installation--Safe Settings Rescue System Memory Test Boot Options | File Help Language 1280 x 1024 Driver 3-11 華碩 PIKE 1064E...
Page 42
4. 將 RAID 驅動程序軟盤放入軟驅。請確認您已選擇 Boot Options 菜單中 的 Installation 選項,然後按下 <Enter>。 Boot from Hard Disk Installation Installation--ACPI Disabled Installation--Local APIC Disabled Installation--Safe Settings Rescue System Memory Test Boot Options | Help Language 1280 x 1024 Driver 5. 當以下畫面出現時,選擇軟驅 (fd0) 作為驅動程序升級媒介。選擇 OK, 然後按下...