Page 1
All manuals and user guides at all-guides.com PICO-BT01 Pico-ITX Board User’s Manual 6 Last Updated: January 18, 2018...
Page 2
All manuals and user guides at all-guides.com Copyright Notice This document is copyrighted, 2018. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
Page 3
All manuals and user guides at all-guides.com Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. ® ITE is a trademark of Integrated Technology Express, Inc. ...
Page 4
All manuals and user guides at all-guides.com Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity PICO-BT01 Product DVD with drivers Heat Spreader COM + Line-out Cable If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
All manuals and user guides at all-guides.com About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product.
Page 6
All manuals and user guides at all-guides.com Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
All manuals and user guides at all-guides.com If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
All manuals and user guides at all-guides.com FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Page 9
All manuals and user guides at all-guides.com China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 及其电子组件 外部信号...
Page 10
All manuals and user guides at all-guides.com China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg)
All manuals and user guides at all-guides.com Table of Contents Chapter 1 - Product Specifications..................1 Specifications ......................2 Chapter 2 – Hardware Information ..................4 Dimensions ....................... 5 Jumpers and Connectors ..................10 List of Jumpers ......................12 2.3.1 Clear CMOS Jumper (JP1 1,3,5) ..............13 2.3.2 Auto Power Button Enable/Disable Selection (JP1 2,4,6) ....
Page 12
All manuals and user guides at all-guides.com 2.4.16 Buzzer Connector (CN21) ..............27 2.4.17 BIO Connector (CN22) ................27 2.4.18 COM Port 1/2 & Line Out Connector (CN23) ........29 2.4.19 MiniCard Slot (Half-Mini Card) (CN24) ..........31 2.4.20 LVDS Port (CN25) ................34 Chapter 3 - AMI BIOS Setup ....................
Page 13
All manuals and user guides at all-guides.com Setup submenu: Save & Exit ................65 Chapter 4 – Drivers Installation .................... 66 Product CD/DVD ....................67 Appendix A - Watchdog Timer Programming ..............69 Watchdog Timer Registers .................. 70 Watchdog Sample Program ................. 71 Appendix B - I/O Information ....................
All manuals and user guides at all-guides.com Specifications System Pico-ITX Form Factor Intel Atom™ Processor E3825 / E3845 ® Processor Intel Celeron Processor J1900 / N2930 / ® ® N2807 up to 2.0 GHz 204-pin DDR3L 1066/1333 MHz SODIMM, up System Memory ...
Page 16
All manuals and user guides at all-guides.com 0 ~ 60°C (32 ~ 140°F ) Operating Temperature -40 ~ 85°C(-40 ~185°F) WiTAS 2 (E3825, E3845) Storage Temperature -40 ~ 80°C (-40 ~176°F) Operation Humidity 0 ~ 90% relative humidity, non-condensing ...
All manuals and user guides at all-guides.com List of Jumpers Please refer to the table below for all of the board’s jumpers that you can configure for your application Label Function JP1 (1,3,5) Clear CMOS Jumper JP1 (2,4,6) Auto Power Button Enable/Disable Selection LVDS Port Operating Voltage Selection JP4 (1,3,5) LVDS Port Backlight Inverter Voltage Selection...
All manuals and user guides at all-guides.com 2.3.1 Clear CMOS Jumper (JP1 1,3,5) Normal (Default) Clear CMOS 2.3.2 Auto Power Button Enable/Disable Selection (JP1 2,4,6) Enable (Default) Disable 2.3.3 LVDS Port Operating Voltage Selection (JP3) +3.3V (Default) 2.3.4 LVDS Port Backlight Inverter Voltage Selection (JP4 1,3,5) +12V +5V (Default) Chapter 2 –...
All manuals and user guides at all-guides.com List of Connectors Please refer to the table below for all of the board’s connectors that you can configure for your application Label Function Battery DDR3L SO-DIMM Slot VGA Port DP port LVDS Port Inverter / Backlight Connector LAN (RJ-45) Port Digital IO Port MiniCard Slot (Full Size)/Default mSATA (feature select by...
All manuals and user guides at all-guides.com 2.4.1 Battery (CN1) Pin Name Signal Type Signal Level +3.3V 3.3V 2.4.2 DDR3L SO-DIMM Slot (CN2) Standard specification 2.4.3 VGA Port (CN3) Pin Name Signal Type Signal level GREEN BLUE RED_GND_RTN GREEN_GND_RTN BLUE_GND_RTN Chapter 2 –...
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level DDC_DATA HSYNC VSYNC DDC_CLK 2.4.4 DP Port (CN4) Pin Name Signal Type Signal level DDI0_DP_D0_P DIFF DDI0_DP_D0_N DIFF DDI0_DP_D1_P DIFF DDI0_DP_D1_N DIFF DDI0_DP_D2_P DIFF DDI0_DP_D2_N DIFF Chapter 2 – Hardware Information...
All manuals and user guides at all-guides.com DDI0_DP_D3_P DIFF DDI0_DP_D3_N DIFF DDI0_DP_AUX_P +3.3V DDI0_DP_AUX_N +3.3V HPLG_DETECT +1.8V RTN_PWR +3.3V 2.4.5 LVDS Port Inverter / Backlight Connector (CN5) BLK_PWR BKL_CONTROL BKL_ENABLE Pin Name Signal Type Signal Level BKL_PWR +5V / +12V BKL_CONTROL Chapter 2 –...
All manuals and user guides at all-guides.com BKL_ENABLE +3.3V * LVDS2/BKL_PWR can be set to +5V or +12V by JP4. * LVDS2/BKL_CONTROL can be set by JP4. * The driving current supports up to 2A 2.4.6 LAN (RJ-45) Port (CN7) ACT/LINK SPEED Pin Name...
All manuals and user guides at all-guides.com 2.4.7 Digital IO Port (CN8) Pin Name Signal Type Signal Level DIO0 DIO1 DIO2 DIO3 2.4.8 MiniCard Slot (Full Size)/Default mSATA (feature select by BOM) (CN9) Pin Name Signal Type Signal level PCIE_WAKE# +3.3V +3.3VSB/+3.3V +1.5V...
Page 33
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level UIM_PWR UIM_DATA PCIE_REF_CLK- DIFF UIM_CLK PCIE_REF_CLK+ DIFF UIM_RST UIM_VPP W_DISABLE# +3.3V PCIE_RST# +3.3V PCIE_RX-/mSATARX+ DIFF +3.3VSB/+3.3V +3.3V PCIE_RX+/mSATARX- DIFF +1.5V +1.5V Chapter 2 – Hardware Information...
Page 34
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level SMB_CLK +3.3V PCIE_TX-/mSATATX- DIFF SMB_DATA +3.3V PCIE_TX+/mSATATX+ DIFF USB_D- DIFF USB_D+ DIFF +3.3VSB/+3.3V +3.3V +3.3VSB/+3.3V +3.3V +1.5V +1.5V Chapter 2 – Hardware Information...
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level +3.3VSB/+3.3V +3.3V 2.4.9 USB Ports 0 and 1 (CN10) Pin Name Signal Type Signal level +5VSB USB0_D- DIFF USB0_D+ DIFF USB0_SSRX− DIFF USB0_SSRX+ DIFF USB0_SSTX− DIFF USB0_SSTX+ DIFF +5VSB Chapter 2 –...
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level USB1_D- DIFF USB1_D+ DIFF * Only Port 0 supports USB 3.0. 2.4.10 USB 2.0 Port 2 (CN11) Pin Name Signal Type Signal Level +5VSB USB2_D- DIFF USB2_D+ DIFF Chapter 2 –...
All manuals and user guides at all-guides.com 2.4.11 +5V Output for SATA HDD (CN14) Pin Name Signal Type Signal Level 2.4.12 SATA Port (CN15) Pin Name Signal Type Signal Level SATA_TX1+ DIFF SATA_TX1- DIFF SATA_RX1- DIFF SATA_RX1+ DIFF Chapter 2 – Hardware Information...
All manuals and user guides at all-guides.com 2.4.14 Front Panel (CN19) Pin Name Pin Name PWR_BTN- PWR_BTN+ HDD_LED- HDD_LED+ SPEAKER- SPEAKER+ PWR_LED- PWR_LED+ H/W RESET- H/W RESET+ 2.4.15 External +12V Input (CN20) Pin Name Signal Type Signal Level +12V +12V Chapter 2 –...
All manuals and user guides at all-guides.com 2.4.16 Buzzer Connector (CN21) Pin Name Signal Type Signal Level 3.3V +3.3V SPEAKER- 2.4.17 BIO Connector (CN22) Pin Name Pin Name +12VSB PCIE_TXN0 PCIE_RXN0 PCIE_TXP0 PCIE_RXP0 PS_ON# +5VSB +5VSB +5VSB +5VSB PCIE_REF_CLK0 RESET# PCIE_REF_CLK0# Chapter 2 –...
Page 41
All manuals and user guides at all-guides.com Pin Name Pin Name USBN0 USBP0 USBN1 USBP2 I2C_CLK or SMB_CLK [Default] I2C_DATA or SMB_DATA [Default] 56 WAKE# USB_OC0# USB_OC1# LPC_AD0 LPC_FRAME# LPC_AD1 SERIRQ LPC_AD2 LPC_DRQ LPC_AD3 PWR_OK/GPIO AGND LPC_CLK AUD_LINEOUT_L PME# AUD_LINEOUT_R Chapter 2 –...
All manuals and user guides at all-guides.com 2.4.18 COM Port 1/2 & Line Out Connector (CN23) Pin Name Signal Type Signal Level DCDB DSRB RTSB ±9V ±9V CTSB DTRB ±9V RIB/+5V/+12V IN/ PWR +5V/+12V DCDA DSRA RTSA ±9V ±9V CTSA DTRA ±9V Chapter 2 –...
Page 43
All manuals and user guides at all-guides.com AGND LOUT_R LOUT_L COM Port 2 RS-485 Pin Name Signal Type Signal level RS485_D- ±5V RS485_D+ ±5V NC/+5V/+12V +5V/+12V COM Port 2 RS-422 Pin Name Signal Type Signal level RS422_TX- ±5V RS422_TX+ ±5V Chapter 2 –...
All manuals and user guides at all-guides.com Pin Name Signal Type Signal level RS422_RX+ RS422_RX- NC/+5V/+12V +5V/+12V * COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. * COM2 RI/+5V/+12V function can be set by BOM(R524-RI/R521-+12V/R526-+5V) 2.4.19 MiniCard Slot (Half-Mini Card) (CN24) Pin Name Signal Type Signal Level...
Page 45
All manuals and user guides at all-guides.com Pin Name Signal Type Signal Level PCIE_REF_CLK- DIFF PCIE_REF_CLK+ DIFF W_DISABLE# +3.3V PCIE_RST# +3.3V PCIE_RX- DIFF +3.3VSB +3.3V PCIE_RX+ DIFF +1.5V +1.5V Chapter 2 – Hardware Information...
Page 46
All manuals and user guides at all-guides.com Pin Name Signal Type Signal Level SMB_CLK +3.3V PCIE_TX- DIFF SMB_DATA +3.3V PCIE_TX+ DIFF USB_D- DIFF USB_D+ DIFF +3.3VSB +3.3V +3.3VSB +3.3V +1.5V +1.5V Chapter 2 – Hardware Information...
All manuals and user guides at all-guides.com Pin Name Signal Type Signal Level +3.3VSB +3.3V 2.4.20 LVDS Port (CN25) Pin Name Signal Type Signal Level BKL_ENABLE BKL_CONTROL LCD_PWR +3.3V/+5V LVDS_A_CLK- DIFF LVDS_A_CLK+ DIFF LCD_PWR +3.3V/+5V LVDS_DA0+ DIFF LVDS_DA0- DIFF LCD_PWR +3.3V/+5V LVDS_DA1+ DIFF...
Page 48
All manuals and user guides at all-guides.com LVDS_DA1- DIFF LVDS_DA2+ DIFF LVDS_DA2- DIFF LVDS_DA3+ DIFF LVDS_DA3- DIFF DDC_DATA DDC_CLK Chapter 2 – Hardware Information...
All manuals and user guides at all-guides.com System Test and Initialization The board uses certain routines to perform testing and initialization. If an error, fatal or non-fatal, is encountered, a few short beeps or an error message will be outputted. The board can usually continue the boot up sequence with non-fatal errors.
All manuals and user guides at all-guides.com AMI BIOS Setup The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system configurations, which is stored in the battery-backed CMOS RAM and BIOS NVRAM so that the information is retained when the power is turned off. To enter BIOS Setup, press <Del>...
All manuals and user guides at all-guides.com 3.4.1 Advanced: ACPI Settings Options summary: ACPI Sleep State Suspend Disabled Optimal Default, Failsafe Default S3 (suspend to RAM) Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
Page 55
All manuals and user guides at all-guides.com Wake on Ring Disabled Optimal Default, Failsafe Default Enabled Enable or disable System Wake on Ring RTC wake system from S5 Disabled Optimal Default, Failsafe Default Fixed Time Enable or disable System wake on alarm event. When enabled, System will wake on the hr::min::sec specified Chapter 3 –...
All manuals and user guides at all-guides.com 3.4.2.2 Super IO Configuration: Serial Port 2 Configuration Options summary: Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Default (Serial Port 1) IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h;...
Page 59
All manuals and user guides at all-guides.com IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Allows BIOS to Select Serial Port resource. Change Settings Auto Default (Serial Port 2) IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; COM2 Type Select RS232 Default RS422 RS485 Select Working model...
All manuals and user guides at all-guides.com 3.4.4 Advanced: CPU Configuration Options summary: Intel Virtualization Disabled Technology Enabled Optimal Default, Failsafe Default When enabled, a VMM can utilize the additional hardware capabilities provided by Vander pool Technology Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com 3.4.5 Advanced: SATA Configuration Options summary: Serial-ATA (SATA) Enabled Default Disabled En/Disable SATA SATA Speed Support Gen1 Default Gen2 SATA Speed Support Gen1 or Gen2 SATA Mode Default AHCI IDE: Configure SATA controllers as legacy IDE AHCI: Configure SATA controllers to operate in AHCI mode Chapter 3 –...
Page 64
All manuals and user guides at all-guides.com Serial-ATA Port x Enabled Default Disabled En/Disable SATA Port SATA Port1 HotPlug Enabled Disabled Default En/Disable SATA Port Hotplug Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com 3.4.6 Advanced: Dynamic Digital IO Configuration Digital Port X Direction Input Output Set DIO as input or Output Digital Port X Level Default Set DIO Output port Hi or Low Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com 3.4.7 Advanced: USB Configuration Options summary: Legacy USB Support Enabled Optimal Default, Failsafe Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected Device Name (Emulation Auto...
Page 67
All manuals and user guides at all-guides.com CDROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex. ZIP drive) Chapter 3 –...
All manuals and user guides at all-guides.com 3.5.1 Chipset: North Bridge Options summary: Primary IGFX Boot Display VBIOS Default Optimal Default, Failsafe Default LVDS Select the Video device LVDS1 Disabled Enabled Optimal Default, Failsafe Default En/Dis LVDS Panel Type 640x480 800x480 Chapter 3 –...
Page 70
All manuals and user guides at all-guides.com 800x600 1024x600 1024x768 Optimal Default, Failsafe Default 1280x768 1366x768 1440x900 Select panel type Color Depth 18Bit Optimal Default, Failsafe Default 24Bit Set color depth Backlight Type Normal Optimal Default, Failsafe Default Inverted Select backlight control signal type Backlight Level 0-100% Select backlight control level...
All manuals and user guides at all-guides.com 3.5.2 Chipset: South Bridge Options summary*: PCIE/mSATA Select PCIE Optimal Default, Failsafe Default mSATA PCIE/mSATA Select * PCIE/mSATA Select is available only for A1.0 version and not available for A1.1 and / or later version.
All manuals and user guides at all-guides.com 3.5.2.1 South Bridge: Azalia HD Audio Azalia HD Audio Disabled Enabled Optimal Default, Failsafe Default Enabling/Disabling HD Audio controller. Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com 3.5.2.3 South Bridge: PCI Express Configuration Options summary: PCI Express Root Port x Enabled Optimal Default, Failsafe Default Disabled Enabling/Disabling PCI Express root ports Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com Setup submenu: Security Change User/Administrator Password You can set a User Password once an Administrator Password is set. The password will be required during boot up, or when the user enters the Setup utility.
Page 76
All manuals and user guides at all-guides.com Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. Chapter 3 – AMI BIOS Setup...
All manuals and user guides at all-guides.com Product CD/DVD The PICO-BT01 comes with a product DVD that contains all the drivers and utilities you need to setup your product. Insert the DVD and follow the steps in the autorun program to install the drivers. In case the program does not start, follow the sequence below to install the drivers.
Page 81
All manuals and user guides at all-guides.com Step 4 – Install Audio Driver Open the Step4 - Audio folder and open the Win7_8-32_64_R273.exe file Follow the instructions Driver will be installed automatically Step 5 – Install USB3.0 Driver Open the Step5 - USB3.0 folder and open the Setup.exe file Follow the instructions Driver will be installed automatically Step 6 –...
All manuals and user guides at all-guides.com Watchdog Timer Registers Table 1 : Watch dog relative IO address Default Value Note I/O Base address for Watchdog operation. I/O Base 0xA00 This address is assigned by SIO LDN7, register Address 0x60-0x61. Table 2 : Watchdog relative register table Register Offset...
All manuals and user guides at all-guides.com Electrical Specifications for I/O Ports Signal Reference Rate Output Name VGA: +5V +5V/0.5A LVDS Port Inverter / Backlight +5V/2A or +12V/2A Connector Digital IO Port D0~D3 +5V/(Open drain) +3.3VSB +3.3V/1.1A Mini-Card Slot +1.5V +1.5V/0.375A +5VSB/1A (per USB 3.0 Port 1 &...
All manuals and user guides at all-guides.com List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Mating Connector Available Cable P/N Label Cable Vendor Model no Battery Molex 51021-0200 Battery 175011901M Cable DDR3 204PIN FOXCONN AS0A626-JER6-7H VGA Connector Astron HDLH-B15-CFHN1T-1-R...
Page 106
All manuals and user guides at all-guides.com Cable CN18 LPC Port SHR-12V-S-B AAEON 1703120130 Cable CN19 Front Panel PINREX 222-97-05GBE1 Front 1701100156 Connector Panel Cable CN20 External +12V Molex 19211-0003 Power 170204010R Input cable CN21 Buzzer PINREX 712-73-02TWE0 Buzzer 170302010C connector Cable CN22...