Related Manuals for Bosch NDV-8502-RX
Summarization of Contents
Safety
Safety Precautions
Installation must be performed by qualified personnel according to electrical codes and local regulations.
Important Safety Instructions
General guidelines for device operation: avoid liquids, heat sources, use proper grounding, and use only specified accessories.
Notices
Includes UL Disclaimer and FCC statement regarding device compliance, performance, and potential interference.
Use Latest Software
Ensures consistent functionality, compatibility, and security by installing the latest software releases.
Old Electrical and Electronic Equipment
Proper disposal guidelines for the product and battery to promote reuse, recycling, and environmental protection.
Short Information
Copyright
This manual is the intellectual property of Bosch Security Systems and is protected by copyright.
Trademarks
Hardware and software product names used in this document are likely registered trademarks.
More Information
Contact nearest Bosch Security Systems location or visit www.boschsecurity.com for additional details.
System Overview
Product Description
Overview of the FLEXIDOME IP indoor 8000i series cameras, their features, and remote commissioning capabilities.
LED Overview
Explanation of the status LED functions and their corresponding meanings for operational status indication.
Intended Use
Designed for professional IP video surveillance; installation and operation require trained professionals.
Preparing for Installation
Unpacking
Instructions for carefully unpacking the equipment and verifying all parts are present and undamaged.
Contents
List of all included components and their quantities provided within the product packaging.
Wiring
Connect the camera to a 10/100 Base-T network using STP Category 5e cable and PoE power.
In-Box Configuration
SD Card Installation
Step-by-step guide for installing one or two microSD cards into the camera's designated compartment.
Hardware Installation
Installing the Mounting Plate
Instructions for securely fixing the camera mounting plate to a flat surface using various mounting holes.
Installing the Mounting Plate Without Conduit
Steps for mounting the plate when the camera's wiring exits directly through the surface.
Installing the Mounting Plate With Conduit
Steps for mounting the plate when the camera's wiring is routed through a conduit.
Wiring the Camera Module
Instructions for connecting the network cable to the camera module for IP5X protection against dust ingress.
Wiring the Camera Module with the IP54 Protection Kit
Steps to wire the camera module using the IP54 kit for protection against dust and water ingress.
Installing the Camera Module
Procedure for attaching the camera module to the prepared mounting plate and securing it.
Mounting Accessories
Details and images of various optional mounting accessories available for the camera system.
Removing the Camera
Steps to safely detach the camera module from its mounting plate after installation.
Commissioning
Commissioning
Guide to setting up the camera using the Project Assistant app, web interface, or Configuration Manager.
Connection via the Web Browser
System Requirements
Computer hardware and software specifications needed to access and configure the camera via its web interface.
Establishing the Connection
Steps to connect to the camera on the network, including finding its IP address and initial setup.
Password Protection in Camera
Procedure for setting a strong service-level password to secure access to the camera's functions.
Troubleshooting
Resolving Problems
A troubleshooting guide with common malfunctions, their causes, and recommended solutions for quick resolution.
Testing the Network Connection
Instructions on how to use the 'ping' command to verify network connectivity and device responsiveness.
Customer Service
Guidance on contacting support for unresolved issues and how to view firmware version information.
Maintenance
Bubble Handling
Guidelines for careful handling of the camera bubble to prevent scratches and maintain optical clarity.
Bubble Cleaning
Recommended procedures for cleaning the interior and exterior surfaces of the camera bubble without damage.
Bubble Replacement
Information on replacing a damaged or yellowed bubble, including available clear and tinted options.
Camera Reset
Step-by-step instructions to reset the camera to its original factory default settings.
Technical Data
Dimensions
Diagram showing the physical dimensions of the camera in millimeters and inches for installation planning.
Specifications
Detailed technical specifications covering power, sensor, optical, streaming, and mechanical aspects of the camera.
Support and Training
Support
Information on accessing Bosch support services, online resources, training courses, and product documentation.
Need help?
Do you have a question about the NDV-8502-RX and is the answer not in the manual?
Questions and answers