Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch FLEXIDOME multi 7000i IR
Summary of Contents for Bosch FLEXIDOME multi 7000i IR
- Page 1 FLEXIDOME multi 7000i IR NDM‑7702‑AL | NDM‑7703‑AL Installation manual...
-
Page 3: Table Of Contents
FLEXIDOME multi 7000i IR Table of contents | en Table of contents Safety Safety message explanation Safety precautions Important safety instructions Notices Short information System overview Product description Intended use Using the camera Operation with external systems Planning information Unpacking... - Page 4 | Table of contents FLEXIDOME multi 7000i IR Transfer Disposal Technical data 10.1 Dimensions 10.2 Specifications 2023-02 | 02 | Bosch Security Systems B.V. Installation manual...
-
Page 5: Safety
FLEXIDOME multi 7000i IR Safety | en Safety Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the device. Safety message explanation In this manual, the following symbols and notations are used to draw attention to special... -
Page 6: Notices
– The camera should be installed at least 10 cm away from the eave of a building. – Please contact Bosch certified dealers for suitable power adapters. – The Low Voltage power supply unit must comply with EN 62368-1. The power supply must be: SELV-LPS unit and Class II for 24 VAC. - Page 7 – Security advisories, that is a list of identified vulnerabilities and proposed solutions: https://www.boschsecurity.com/xc/en/support/product-security/security-advisories.html Bosch assumes no liability whatsoever for any damage caused by operating its products with outdated software components. Bosch Security Systems B.V. 2023-02 | 02 |...
-
Page 8: Short Information
Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between this manual and the product described. Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. -
Page 9: System Overview
System overview Product description The FLEXIDOME multi 7000i IR camera is built for high-quality performance, featuring four independent imagers with motorized zoom/focus lenses. It helps to simplify installation and lower costs while maintaining flexibility in coverage. With four scenes simultaneously in a single camera, it is perfect for wide area coverage, traffic intersections and building corners. -
Page 10: Intended Use
Integration with the many Bosch recording solutions is seamless. Operation with external systems The web browser is the most direct way of using the camera, however, the Bosch download store provides several other free applications (listed below) for viewing and controlling the camera. - Page 11 Video Security Client The Video Security Client is a free, easy-to-use video-surveillance application provided by Bosch for local and remote monitoring of IP cameras and appliances. The software supports up to 16 cameras. The Video Security Client has extensive dewarping capabilities and can be used for client-side dewarping as well as for viewing the available modes.
-
Page 12: Planning Information
This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all parts are included. If any items are missing, notify your Bosch Security Systems sales or customer service representative. -
Page 13: Preparation
Screwdriver and bit holder for TR20 bit, or use the provided TR20 Allen key. – microSD card (optional) Note: Bosch recommends the use of industrial microSD cards with health monitoring. – Wireless USB dongle (NCA-WLAN) for wireless commissioning (optional) - available 2022. -
Page 14: Installation
| Installation FLEXIDOME multi 7000i IR Installation Installing the mounting plate The mounting plate is used to fix the camera to a flat surface. It offers different holes and slots for a variety of fixing options. 1 PIP Mounting holes for installation with Mounting holes for 4 inch or 4S... -
Page 15: Installing The Mounting Plate Without Conduit
FLEXIDOME multi 7000i IR Installation | en Notice! The plugs and screws for surface mounting are not supplied with the camera. 5.1.1 Installing the mounting plate without conduit Remove the mounting plate from the box. Position the mounting plate with the center hole on top of the cable exit on the surface, and mark the positions of the screw holes on the surface. - Page 16 | Installation FLEXIDOME multi 7000i IR Put the cable through the hole of the conduit plate. Attach the conduit plate with the conduit plate adapter to the surface with a 5-6 mm (0.2 inch) screw. Remove the mounting plate from the box.
-
Page 17: Installing The Camera Base
Local storage Notice! Bosch recommends the use of industrial micro SD cards with health monitoring. If necessary, install a micro SD card in the micro SD slot. Press the micro SD card firmly until it latches into place in the slot. -
Page 18: Installation Steps
| Installation FLEXIDOME multi 7000i IR Grounding Warning! Trained electricians only! Work at electric appliances must only be carried out by qualified technicians. To ground the camera: Remove the screw from the bottom of the camera base. Install the ring terminal (not supplied with the camera) on the screw. - Page 19 FLEXIDOME multi 7000i IR Installation | en Put the RJ-45 punch-through aid on the network cable. Remove the tubes from the M20 rubber grommets. Put one M20 rubber grommet on the edge of the RJ-45 punch-through aid. Pull the RJ-45 punch-through aid together with the network cable connector through the M20 rubber grommet.
- Page 20 | Installation FLEXIDOME multi 7000i IR Put the other M20 rubber grommet on the edge of the auxiliary connections cable. Leave at least 5 cm (2 inch) between grommet and end of the cable. Slightly pull back the M20 rubber grommets on both cables to make sure that the grommet sleeve faces the source of the cables.
- Page 21 FLEXIDOME multi 7000i IR Installation | en 12. If required, do a loop with the cable on the hooks of the mounting plate. 13. Position the camera base on the mounting plate, so that the screw holes of camera base and mounting plate match.
-
Page 22: Wiring The Camera Base
| Installation FLEXIDOME multi 7000i IR 5.2.3 Wiring the camera base Network connection Connect the network cable to the network connector. Auxiliary connections - power connection Notice! IP66 water/dust protection For IP66 water/dust protection, use cables with a diameter of at least 5 mm. - Page 23 FLEXIDOME multi 7000i IR Installation | en Notice! If PoE++ or PoE+ is not available, use a 24V AC power supply. Remove 8 mm (0.3 inch) of the power wires insulation. Connect the power wires to the 2-pin power connector. Connect the 2-pin power connector to the power connector of the camera base.
-
Page 24: Connecting A Wireless Usb Dongle
The camera is equipped with a USB-C port for a wireless USB dongle (sold separately, available 2022), so that you can easily perform the initial configuration wirelessly. Using a mobile device with the Bosch Project Assistant app, you can do initial set-up and lens zoom- focus to find the right scene. -
Page 25: Setting The Position Of The Multi-Imager Lenses
FLEXIDOME multi 7000i IR Installation | en Setting the position of the multi-imager lenses You can set the position of each multi-imager lens individually to achieve maximum flexibility. You can do the following 4-axis lens adjustments: Panning each of the four lenses over the ring, page 25 : 0º to 360º... -
Page 26: Tilting Each Of The Four Lenses
| Installation FLEXIDOME multi 7000i IR 5.3.2 Tilting each of the four lenses Tilt the each of the four lenses to set the position that you need. You can tilt 0° to 105°. 0º ~ 105° To set each of the four lenses at 90° tilt, to let the lens face straight down in ceiling installations, make sure that the white dot in the middle of the larger lens holder meets the edge of the smaller lens holder. -
Page 27: Rolling Each Of The Four Lenses
FLEXIDOME multi 7000i IR Installation | en Notice! Mechanically, each of the four lenses rotates -45º to 45º, but doing so will prevent you from closing the camera dome cover. Do not rotate more than -20º to 20º. -20º ~ 20°... -
Page 28: Installing The Camera Dome Cover
| Installation FLEXIDOME multi 7000i IR Installing the camera dome cover Position the camera dome cover on the camera base, so that the triangle icons on the camera base and on the camera dome cover match. Tighten the 6 captive screws of the screw holes in the camera dome cover between 1 and 2 Nm. - Page 29 FLEXIDOME multi 7000i IR Installation | en NDA-U-WMT Universal wall mount for dome cameras, white. NDA-U-WMP Back plate for universal wall mount, corner mount and pole mount, white, IP66. NDA-U-PMT Universal pipe mount for dome cameras, 31 cm, white. NDA-U-PMTE Extension for universal pipe mount, 50 cm, white.
- Page 30 | Installation FLEXIDOME multi 7000i IR NDA-U-PMAL Universal pole mount adapter, white; large. NDA-U-RMT Universal roof mount for dome cameras, white. NDA-U-PA0 Surveillance cabinet, 24 VAC input, 24 VAC output, IP66. NDA-U-PA1 Surveillance cabinet, 100 - 120 VAC 50/60 Hz input, 24 VAC output, IP66.
- Page 31 FLEXIDOME multi 7000i IR Installation | en SFP-3 SFP Fiber Optic Module, 20 km (12.4 miles), 2 LC connectors. Single-mode. 1310 nm. SFP-25 SFP Fiber Optic Module, 2 km (1.2 miles), 1 SC connector. Multi-mode. 1310/1550 nm. SFP-26 SFP Fiber Optic Module, 2 km (1.2 miles), 1 SC connector. Multi-mode. 1550/1310 nm.
-
Page 32: Configuration
FLEXIDOME multi 7000i IR Configuration Bosch Project Assistant If you have connected a wireless USB dongle, you can use the Bosch Project Assistant app on a mobile device (iOS, Windows, or Android) to perform the initial configuration wirelessly. Download the Project Assistant app. -
Page 33: Video Security Client
Video Security Client The Video Security Client is a free, easy-to-use video-surveillance application provided by Bosch for local and remote monitoring of IP cameras and appliances. The software supports up to 16 cameras. The Video Security Client has extensive dewarping capabilities and can be used for client-side dewarping as well as for viewing the available modes. -
Page 34: Troubleshooting
| Troubleshooting FLEXIDOME multi 7000i IR Troubleshooting Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution Unit does not operate. Power failure. Check power supply. Check if PoE+ or 24 V auxiliary input is... -
Page 35: Customer Service
FLEXIDOME multi 7000i IR Troubleshooting | en – The device is not properly connected to the network. Check the cable connections in this case. – The device is not correctly integrated into the network. Check the IP address, subnet mask, and gateway address. -
Page 36: Maintenance
Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com... - Page 37 FLEXIDOME multi 7000i IR Maintenance | en Re-attach the camera dome cover onto the camera base. Bosch Security Systems B.V. 2023-02 | 02 | Installation manual...
-
Page 38: Decommissioning
| Decommissioning FLEXIDOME multi 7000i IR Decommissioning Transfer The device should only be passed on together with this Installation manual. Disposal Old electrical and electronic equipment This product and/or battery must be disposed of separately from household waste. Dispose such equipment according to local laws and regulations, to allow their reuse and/or recycling. - Page 39 FLEXIDOME multi 7000i IR Technical data | en Technical data 10.1 Dimensions Dimensions in mm (inch) 10.2 Specifications Power Input voltage 45 W (PoE 802.3bt Type 3 Class 5 with operating temperature -50 °C to +55 °C (-58 °F to +131 °F) 30 W (PoE 802.3at Type 2 Class 4 with operating temperature -20 °C to +55 °C (-4 °F to +131 °F)
- Page 40 | Technical data FLEXIDOME multi 7000i IR Power Power Consumption PoE++: 10.6 W / 42.3 W (typical / maximum) PoE+: 10.6 W / 21.8 W (without heater) Sensor Sensor type 4x 1/2.7‑inch CMOS Sensitivity Measured according to IEC 62676 Part 5 (1/25, F1.9) Color 0.091 lx...
- Page 41 FLEXIDOME multi 7000i IR Technical data | en Video streaming GOP structure Frame rate 1-30 fps Signal-to-Noise Ratio (SNR) >55 dB Video resolution (H x V) Max. resolution (12 MP 4x 2048 x 1536 (4:3) @30 fps variant) 4x 1920 x 1080 (16:9) @30 fps Max.
- Page 42 | Technical data FLEXIDOME multi 7000i IR Video content analysis Alarm rules (combinable) Any object, Object in field, Line crossing, Enter / leave field, Loitering, Follow route, Idle / removed object, Counting, Occupancy, Crowd density estimation, Condition change, Similarity search, Flow / counter flow...
- Page 43 FLEXIDOME multi 7000i IR Technical data | en Audio streaming Standard G.711, 8 kHz sampling rate L16, 16 kHz sampling rate AAC-LC, 48 Kbit/s at 16 kHz sampling rate AAC-LC, 80 Kbit/s at 16 kHz sampling rate Signal-to-Noise Ratio >50 dB Audio Streaming Full-duplex / half duplex...
- Page 44 Troubleshooting – Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2023-02 | 02 | Bosch Security Systems B.V. Installation manual...
- Page 45 FLEXIDOME multi 7000i IR Technical data | Bosch Security Systems B.V. 2023-02 | 02 | Installation manual...
- Page 46 | Technical data FLEXIDOME multi 7000i IR 2023-02 | 02 | Bosch Security Systems B.V. Installation manual...
- Page 48 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2023 Building solutions for a better life. 202302231532...