Related Manuals for CDVI DWPS102U
Summarization of Contents
Machinery Directive
Instructions for use
Guidance on operating and safely using the automatic door system.
Declaration of the Manufacturer
Formal declaration by the manufacturer regarding product compliance with directives.
Accessories
Mounting kit
Components and quantities for mounting the DIGIWAY PLUS operator.
Mounting diagram
Accessories
Visual representation of sliding and articulated arm accessory configurations.
Technical specifications
General specifications
Detailed technical data including power, torque, dimensions, and operating conditions.
Use conditions
Defines operational zones and their corresponding cycle usage per day.
Electronic card specifications
Details input/output signals, operating modes, and interface specifications.
Main features
Lists key functionalities and operational modes of the DIGIWAY PLUS operator.
Installation
Sliding arm version
Step-by-step instructions for installing the operator with a sliding arm mechanism.
Wiring diagram
Electronic card layout and programming buttons
Diagram showing the layout of the electronic card and its programming buttons.
Jumper for external switch exclusion
Instructions for using a jumper to exclude the external switch functionality.
Electrical connections
Connections detail
Detailed breakdown of terminal block connections for motors, sensors, and power.
Monitored photocells wiring
LOW ENERGY mode
Parameters and calculations for operating the door in Low Energy mode for safety.
Electronic card LED's
Meaning of LP LED messages
Explanation of the status and error indications provided by the LP LED on the electronic card.
Battery
Details on the operator's battery specifications, autonomy, and lifespan.
GETTING STARTED
Initial steps and overview of the operator's configuration using the LCD and keyboard.
ACCESS to the MAIN MENU
Procedure to access the main menu structure for configuration and settings.
Guided configuration
STEP I: INITIAL SETUP
First step in configuration: language selection and transmitter memorization.
STEP II: CONFIGURATION
Door Operation Modes
Configuration of operational modes like Auto, Door Free, Always Open, Day/Night, and Spring.
Safety and Advanced Features
Settings for safety inputs, radar modes, double door overlap, and fire signal.
Arm and Door Type Settings
Configuration of arm type, door type (master/slave), and door opening/closing behavior.
Electrolock and Jolt Settings
Configuration of electrolock, opening jolt, and push-to-open/close functionalities.
STEP IV: ADJUSTMENTS
CURRENT CALCULATION CYCLES
Explanation of post-calibration cycles for obstacle management calculation.
ADJUSTMENTS
Manual adjustment of speed, torque, and pause time parameters.
STEP IV: ADJUSTMENTS (continued...)
STEP V: ADVANCED SETTINGS
Introduction to advanced parameters for fine-tuning installation and operation.
STEP V: ADVANCED SETTINGS (Continued...)
Electrolock and Delay Settings
Adjusts electrolock release time, opening jolt, and adds an open delay.
Torque and Wind Stop Settings
Adjusts motor torque for opening jolt and wind stop functionality.
Advanced Settings Parameters
Obstacle Detection and Approach Speed
Configures obstacle reaction behavior and door approach speed.
Cycle Types and Low Energy
Sets obstacle detection cycle type and parameters for Low Energy mode.
Disabled persons access settings
Remote controls management
Procedure for memorizing, deleting, and managing remote control transmitters.
Menu Service
Absolute Counter
Registers the motor's total operational cycles, not resettable by the factory.
Partial Counter
Counter for maintenance periods, resettable after service intervention.
Information
Display modes (Expert/Normal)
Sets the information displayed on the LCD screen for operator status and parameters.
Factory Defaults
Resets all operator parameters to their original factory values.
System Reset
Restarts the system, equivalent to a power cycle, recalculating current values.
Double door configuration
Part I: Mechanical fixing
Instructions for the mechanical installation of the double door structure.
Part I: Mechanical fixing (continued)
Motor fixing
Procedure for securing each motor unit to the back-plate.
Door guides fixing (inward opening)
Steps for attaching the door guides for inward opening doors.
Articulated arm fixing (outward opening)
Steps for attaching the articulated arm components for outward opening doors.
Mechanical check
Verifies the fluency of motion and side switch positions after mechanical installation.
Part II: Electrical connections
Master/Slave unit identification
Defines the roles of MASTER and SLAVE units in a double door setup.
Safety devices connection
Methods for connecting safety photocells to the electronic card.
Part III: Final set-up
Engage Position setting
Sets the point for leaves to open/close without interference in overlapping doors.
Slave unit configuration
Configures parameters for the SLAVE unit in a double door system.
Master unit configuration
Configures parameters for the MASTER unit in a double door system.
Maintenance
Sliding arm checks
Periodic checks for sliding arm components, guide, and motor shaft.
Articulated arm checks
Periodic checks for articulated arm components, knee, and adjustable forearm.
Use Instructions
Setting Door Modes
Instructions for setting Automatic, Always Open, Door Free, and Night modes.
Battery Operation
Indication of battery status when the operator is running on battery power.
Need help?
Do you have a question about the DWPS102U and is the answer not in the manual?
Questions and answers