Related Manuals for Lincoln Electric K3328-1
Summarization of Contents
Introduction
General Physical Description
Details the physical attributes and modular design of the wire feeder.
Installation and Operator Instructions
Guides users through the setup and operational procedures.
Installation and Operator Instructions
Bench Configurations
Describes configurations where the user interface is mounted directly to the wire drive.
Boom Configurations
Details configurations where the user interface is in a separate control box.
Installing Drive Rolls
Wire Drive Pressure Setting
Guidance on adjusting drive roll pressure for optimal wire feeding.
Pinion Gear Ratio
Shielding Gas Connection
Steps for connecting the shielding gas supply to the equipment.
Water-Cooled Gun Connections
Instructions for connecting water-cooled gun components.
Loading Spools of Wire
Electrical Installation
Guidance on connecting welding cables and power sources.
Welding with Multiple Arcs
Control Cable
Details on ArcLink control cables and their specifications.
Trigger Connector (5 pin)
ArcLink Connector (5 pin)
Description of the 5-pin ArcLink connector and its wiring.
Graphic Symbols on Interface
Explanation of symbols used on the Power Feed 84 interface and manual.
User Interface Layout
Wire Feed Speed/Amps Display and Knob
Details on adjusting wire feed speed and amperage via the display and knob.
Gas Flow Sensor Kit Operation
Selecting a Weld Mode
Procedure for selecting welding modes via the user interface.
4-Step Trigger: Special Considerations
Start Options
Available start options and their effects on weld initiation.
End Options
Wire Drive Selection
How to select the active wire drive when multiple are connected.
Cold Feed
Functionality for feeding wire forward without initiating welding.
Gas Purge
Gouging Kit Operation
How to operate the wire feeder with a gouging kit installed.
Dual Procedure and Memory Operation
Managing dual procedures and saving/recalling weld memories.
Limits
Enabling/Disabling Limits
How to enable or disable parameter limits for specific memories.
Enabling/Disabling Limits
Usb Operation
Using the USB port for loading and storing memories.
Set-Up Menu: Basic Configuration
Wire Feed Speed Units
Selecting units for displaying wire feed speed (English or Metric).
Arc Display Mode
Choosing what value is displayed on the left display during welding.
Display Options
Selecting information displayed on the alphanumeric displays during welding.
Set-Up Menu: Procedure & Offset
Procedure Change Method
Selecting how remote procedure selection (A/B) is made.
Gun Offset Adjustment
Adjusting the wire feed speed calibration for push-pull guns.
Set-Up Menu: Gas & Gun Control
TIG Gas Control
Controlling which gas solenoid actuates during TIG welding.
Push Pull Gun Knob Behavior
Defining how the potentiometer on a push-pull gun behaves.
Set-Up Menu: Remote Control
Remote Control Type
Selecting the type of analog remote control being used.
Set-Up Menu: Drive & Display
Wire Drive Gear Ratio
Selecting the wire drive gear ratio for optimal performance.
Wire Drive Direction
Setting the wire drive direction for single wire feeders.
Display Trim as Volts Option
Determining if trim is displayed as voltage.
Set-Up Menu: USB Memory
USB Options - Load User Mems & P-Nums from USB
Loading user memories and parameters from a USB drive.
USB Options - Save User Mems & P-Nums to USB
Saving user memories and parameters to a USB drive.
Set-Up Menu: Gas & Polarity
Gas Flow Units
Choosing units for displaying gas flow (cfh or l/min).
Electrode Polarity
Selecting electrode voltage sense polarity (Positive or Negative).
Set-Up Menu: Diagnostics & Modes
Show Test Modes
Option to include or exclude test weld modes from the list.
View Diagnostics
Accessing diagnostic options for servicing and troubleshooting.
Set-Up Menu: Memory & Security
Memory Change Lockout
Determining if memories can be overwritten with new contents.
Setup Menu Lock
Controlling if the setup menu can be modified without a passcode.
Set-Up Menu: USB Functionality
USB Options
Enabling and disabling specific USB options on the feeder.
USB Prompt
Enabling or disabling the USB prompt when a drive is plugged in.
Suggested Accessories
Drive Roll and Wire Guide Kits
Various drive roll and wire guide kits for different wire types.
Gun Adapter Kits
Kits for adapting different types of welding guns to the feeder.
Need help?
Do you have a question about the K3328-1 and is the answer not in the manual?
Questions and answers