Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Dell EMC S4148F-ON
Summarization of Contents
About this guide
Related documents
Lists related documentation for the S4100-ON Series switches.
Information symbols
Explains the meaning of information symbols used in the guide.
S4100-ON Series Switch
Introduction
Provides an overview of the S4100-ON Series switches and their capabilities.
Features
Details the key features and capabilities of the S4100-ON Series switches.
Physical dimensions
Lists the physical dimensions of the S4100-ON Series switches.
LED display
Describes the LED displays on the I/O and PSU sides of the switch.
LED behavior
Explains the behavior of the switch LEDs during ONIE operations.
Prerequisites
Lists the required and optional components for installing the S4100-ON Series switch.
S4100-ON Series configurations
Details the different configurations available for the S4100-ON Series switches.
Luggage tag
Describes the pull-out luggage tag on the PSU-side of the switch.
Site Preparations
Site selection
Specifies requirements for selecting an appropriate installation site for the switch.
Cabinet placement
Provides guidelines for placing the switch within a cabinet for proper airflow and access.
Rack mounting
Details the requirements for grounding the equipment rack and the switch.
Switch ground
Recommends grounding procedures for the switch for safety and compliance.
Fans and airflow
Explains the airflow options supported by the switch fans.
Power
Describes how to connect the switch to a power source.
Storing components
Provides guidelines for properly storing the switch and its components when not in use.
S4100-ON Series Installation
Unpack the switch
Details the procedure for unpacking the switch and verifying included items.
Rack or cabinet installation
Explains how to mount the switch in a rack or cabinet.
ReadyRails installation
Guides the user through installing the ReadyRails rack mounting system.
Switch Installation
Covers the general installation of the switch into the rack rails.
Optics installation
Provides instructions for installing optical transceivers into the switch ports.
Switch power-up
Describes the steps and recommendations before powering up the installed switch.
After switch installation
Guides on post-installation configuration and software setup.
Switch replacement
Outlines the procedure for removing and replacing a switch.
Power Supplies
Components
Lists the available power supply options for the S4100-ON Series switch.
AC or DC power supply installation
Details the procedure for installing AC or DC power supply units.
AC or DC power supply replacement
Explains how to replace a failed AC or DC power supply unit.
Fans
Components
Identifies the available fan components for the S4100-ON Series switch.
Fan module installation
Guides the user on how to install a fan module into the switch.
Fan module replacement
Explains the procedure for replacing a failed fan module.
Management Ports
RS-232 console port access
Details how to connect to the switch using the RS-232 console port.
USB-B console port access
Explains how to connect to the switch using the USB-B console port.
USB storage mount
Describes how to mount USB storage devices for file transfers.
Before you install an OS
Explains the POST process and Grub bootloader after initial power-on.
Grub bootloader example
Provides an example of the Grub bootloader interface.
ONIE example
Provides examples of ONIE operations and commands.
Check your switch
Guides on how to verify ONIE is working properly.
ONIE service discovery
Explains how ONIE discovers the installer through various methods.
Specifications
Chassis physical design
Lists the physical dimensions and weight of the switch chassis.
Environmental parameters
Details the operating and storage environmental conditions for the switch.
AC power requirements
Specifies the AC power requirements for the switch.
IEEE standards
Lists the IEEE standards the switch complies with.
Agency compliance
Covers various agency compliance statements for the switch.
USA Federal Communications Commission statement
Provides the FCC compliance statement for Class A digital devices.
European Union EMC directive conformance statement
Details the EMC directive conformance statement for the European Union.
Japan VCCI compliance for class A equipment
States compliance with Japan's VCCI standards for Class A equipment.
Korean certification of compliance
Lists the Korean certification details for the switch.
Safety standards and compliance agency certifications
Lists various safety and compliance certifications.
Electromagnetic compatibility
Covers emissions and immunity standards for electromagnetic compatibility.
Product recycling and disposal
Provides information on recycling and disposal of the product.
Need help?
Do you have a question about the S4148F-ON and is the answer not in the manual?
Questions and answers