Related Manuals for PENKO SGM740
Summarization of Contents
Important Safety Information
General Safety Guidelines
Adherence to instructions for safe installation, operation, and maintenance.
Load Cell and Power Connections
SGM700 Basic Digitizer Connections
Details wiring connections for the basic SGM700 model.
SGM710 Digitizer Analog Connections
Details wiring connections for the SGM710 analog model.
SGM720 Digitizer Ethernet Connections
Details wiring connections for the SGM720 Ethernet model.
SGM730 Digitizer CAN Connections
Details wiring connections for the SGM730 CAN model.
SGM740 Digitizer Profibus Connections
Details wiring connections for the SGM740 Profibus model.
SGM750 Digitizer Serial Connections
Details wiring connections for the SGM750 Serial model.
Display Indications
Display Status Indicators
Explains the meaning of indicators like 'Weigher stable' and 'Zero active'.
Keypad Operation Modes
Describes different functions based on key press duration and mode.
Front Panel Key Functions
Key 1 Functions
Details the short and long press functions of Key 1 in weighing and menu modes.
Key 2 Functions
Details the short and long press functions of Key 2 in weighing and menu modes.
Key 3 Functions
Details the short and long press functions of Key 3 in weighing and menu modes.
Initial Indicator Setup
Configuration Menu Structure
Outlines the hierarchy and options within the configuration menu.
Weigher Settings
Guides through setting the maximum net weight value and display step size.
Calibration Procedure
Step-by-step instructions for performing zero and gain calibration.
Configuration via PI Mach II Software
Explains how to configure the device using dedicated software.
Main Menu Operations
Setpoint Adjustment
Allows adjustment of output switching levels for different operations.
Traceable Access Code (TAC)
Displays the count of indicator data changes for traceability.
Calibration Counter (CAL Code)
Shows the number of times calibration has been modified.
Configuration Menu
Setpoint Function Settings
Configures output switching modes for various weighing functions.
Setpoint Action Settings (Hysteresis)
Sets hysteresis values for output switching to ensure stable operation.
Analog Output Settings
Configures parameters for the analog output signal.
Local Bus Communication (RS485)
Sets communication parameters for the RS485 local bus.
Ethernet Settings (SGM720)
Configures network settings for Ethernet communication on SGM720.
CAN Bus Settings (SGM730)
Configures communication parameters for the CAN bus on SGM730.
Profibus Settings (SGM740)
Configures communication parameters for Profibus on SGM740.
RS232 Port Settings (SGM750)
Configures serial communication parameters for RS232 on SGM750.
RS422 Port Settings (SGM750)
Configures serial communication parameters for RS422 on SGM750.
Indicator Settings
Adjusts various display parameters like max value, step size, and decimal point.
Multi Range/Interval Settings
Configures settings for multi-range operation and auto-ranging.
Filter Settings
Adjusts display filter band and factor for a calm display view.
Digital Filter Settings
Configures digital filters for signal processing and noise reduction.
Pre-calibration Settings
Sets initial parameters before the main calibration process.
Calibration Settings
Guides through adding, checking, and deleting calibration points.
Theoretic Calibration
Allows calibration using loadcell specifications without a reference weight.
Geographic Calibration
Sets geographical information for loadcell origin and location.
Date and Time Configuration (SGM750)
Sets the internal date and time for the SGM750 unit.
Firmware Update
Updating Firmware via USB
Step-by-step guide for updating the device firmware using PI Mach II software.
Setting Boot Mode for Update
Describes how to put the SGM700 into boot mode for firmware updates.
Error Codes and Troubleshooting
General Error Codes
Lists common error codes and their corresponding solutions for parameter and system errors.
Weigher Specific Error Codes
Details error codes specific to the weigher functionality like overflow and underflow.
Profibus Protocol Description
PLC Data Exchange
Details data words, bits, and commands for communication with a PLC.
Standard Factory Settings
Default Configuration Values
Lists default settings for setpoints, actions, and analog outputs.
Network and Indicator Defaults
Lists default values for Ethernet, indicator, filter, and digital filter settings.
Calibration and Geographic Defaults
Lists default settings for pre-calibration, theoretical calibration, and geographic calibration.
Appendix I: Function Definitions
Weighing Function Definitions
Defines terms like Weight, Fast Gross, Display Gross, Tare, Peak, and Signal.
Need help?
Do you have a question about the SGM740 and is the answer not in the manual?
Questions and answers