Related Manuals for Projecta IC1000
Summarization of Contents
Important Safety Information
General Safety Warnings
Crucial safety advice including ventilation, indoor use, and handling damaged cords.
Features
7-Stage Automatic Charging
Fully automatic battery charger with 7 charge stages for optimal battery life.
Desulphation Stage
Breaks down sulphation in flat batteries using high-frequency pulses.
Soft Start Stage
Gentle preliminary charge process to protect battery and increase life.
Bulk Charge Stage
Charges at maximum rate (constant current) to approx. 80% charge.
Charger Functions
Absorption, Equalisation, Analysis, Recondition Stages
Details absorption, calcium equalisation, battery analysis, and recondition modes.
Float Stage and Adjustable Rate
Explains float stage maintenance and adjustable charge rate for optimal charging.
Multi Chemistry and Power Supply Modes
Covers multi-chemistry selection and power supply mode for appliances.
Model-Specific Accessories
Describes wiring harness and rubber end caps for specific charger models.
Charge Status Indicator and Technology
LED Patterns for Charging Stages
Explains LED illumination and flash patterns indicating charging stages.
Polarity and Over Temperature Protection
Safeguards against reverse connections and overheating with automatic shutdown.
Switchmode Technology and Cooling Fan
Details lightweight switchmode design and thermostatically controlled cooling fan.
Remote Control Display
Optional display for monitoring and controlling the charger remotely.
Specifications
Model Specifications
Lists type, input, output, voltage, current, and minimum start voltage for models.
Charge Control Details
Outlines parameters for Desulphation, Soft Start, Bulk, Absorption, etc.
Power Supply and Battery Range
Specifies power supply voltage and supported battery ranges.
Battery Types and Dimensions
Lists compatible battery types and physical dimensions.
Weight
Provides the weight for different charger models.
Product Overview and Dimensions
Charger Components and Controls
Identifies key components like LEDs, buttons, fans, and connection points.
Model-Specific Diagrams and Dimensions
Shows physical layouts, dimensions, and connection details for models.
Accessories and Connections
Illustrates vehicle harness, battery clips, and ring terminals for connection.
Charging Instructions
Step 1: Check Electrolyte Level
Procedure for checking and topping up electrolyte levels in non-sealed batteries.
Step 2A: Connection Out of Vehicle
Instructions for connecting the charger to a battery outside of a vehicle.
Step 2B: Connection In Vehicle (Negatively Earthed)
Guide for connecting the charger to a vehicle's chassis or terminal.
Connection Procedures and Settings
Step 2B: Connection In Vehicle (Positively Earthed)
Instructions for connecting the charger to a positively earthed vehicle.
Step 2C: Connection In Vehicle with Harness
Details on using the vehicle harness for connecting the charger.
Step 3 & 4: Connect to Mains and Set Charge Rate
Procedure for connecting to power and selecting the appropriate charge rate.
Charge Rate, Battery Chemistry, and Disconnection
Adjustable Charge Rates Table
Table providing recommended current settings for 12V batteries by AH, CCA, MCA.
Step 5: Set Battery Chemistry Type
Guide to selecting the correct battery chemistry for optimal charging.
Step 6 & 7: Charging Process and Disconnection
Monitoring charge stages and safe procedures for disconnecting the charger.
Mounting and Permanent Wiring
Step 8: Check Electrolyte Level (Calcium Mode)
Procedure for checking and topping up electrolyte for Calcium batteries.
Mounting Instructions
Guidelines for safely mounting the charger for optimal ventilation.
Permanent Wiring to Battery
Instructions for hardwiring the charger's DC leads for permanent installations.
Battery Chemistry Selection Details
Permanent Wiring Fuse Installation
Guidance on fitting the correct rated fuse for permanent wiring.
Battery Chemistry Selection Procedure
Steps to select the correct battery chemistry type for charging.
Power Supply Mode
Details on using the charger as a 13.8VDC power supply for appliances.
GEL, AGM, and WET Battery Charging Modes
Explanation of specific voltage profiles for GEL, AGM, and WET batteries.
Advanced Modes and Fault Codes
Calcium Battery Charging Mode
Suitable for deeply discharged Calcium batteries requiring equalization up to 16V.
Locking the Battery Charger Settings
Procedure to lock/unlock charger settings to prevent accidental changes.
Fault Codes and Remedies
Identifies error codes displayed by LEDs and provides troubleshooting steps.
Frequently Asked Questions
Determining Battery Charge Status
How to know if the battery is charged using LEDs or a hydrometer.
Troubleshooting Charging Issues
Addresses issues like the charging LED not coming on and low voltage charging.
Using Charger as Power Supply
Guidance on using the charger for appliances and maintaining vehicle settings.
Understanding Charger Reset and Stage Indicators
Explains charger resets with loads and how to interpret LED stage indicators.
Operational Scenarios and Battery Types
Bypassing Desulphation/Soft Start Modes
How to bypass initial stages using Power Supply mode for faster charging.
Appliance Load During Charging
Impact of appliances on charging and recommendation for Power Supply mode.
Selecting Battery Chemistry
Flexibility in selecting battery chemistry if charge voltages match.
Calcium Battery Charging and Modes
Reasons for long Calcium charging times and the need for special modes.
What is a Calcium Battery?
Explanation of Calcium battery composition and its benefits.
Warranty Statement
Warranty Coverage and Exclusions
Details warranty period, coverage, and exclusions for product defects.
Making a Warranty Claim
Procedure for consumers to make a warranty claim, including required documentation.
Consumer Rights and Guarantees
Information on consumer rights under Australian Consumer Law and guarantees.
Distribution Information
Contact details for distributors in Australia and New Zealand.
Need help?
Do you have a question about the IC1000 and is the answer not in the manual?
Questions and answers