Dvd Audio - Denon DVD-3910 Operating Instructions Manual

(9) HDMI connections
A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-Definition Multimedia Interface)
connector allows digital transfer of the digital images of DVD video and other sources, DVD video, and the multi-channel sound of DVD
audio.
DVD-3910
Monitor equipped with
HDMI input connectors
Connection Examples for HDMI AUDIO SETUP
HDMI-supported monitor or projector, etc. (2-channel support or no audio support)
• 2CH························Use this connection when you would like to enjoy the multi-channel audio output from an analog audio output
connector, DENON LINK, or with the audio output from an IEEE 1394 connector.
HDMI-supported monitor/AV amplifier, etc. (Supports DTS and Dolby Digital decoders)
• MULTI (NORMAL)···Use this connection when you would like to enjoy the multi-channel audio output from an HDMI connector and you
wish to have a DTS, Dolby Digital, or other decoder connected to do the processing. (Speaker and other settings
are not required.)
HDMI-supported monitor (Supports audio input for 2 or more channels)
• MULTI (LPCM) ·······Use this connection when you would like to enjoy the multi-channel output from an HDMI connector and the
connection point does not support a DTS, Dolby Digital, or other decoder. (Speaker settings are permitted.)
NOTES:
• HDMI audio output settings permit the selection of either 2
channels or multi-channels. When selecting MULTI (NORMAL)
or MULTI (LPCM), a down-mixed audio signal is only output from
the analog connectors (Left/Right and Front Left/Front Right) of
the DVD-3910. To output multi-channel sound from the analog
audio output connectors, set HDMI to OFF, or select "2CH".
• When selecting MULTI (NORMAL) or MULTI (LPCM), the
settings of "IEEE1394" and "DENON LINK" under "DIGITAL
INTERFACE SETUP" of "SETUP" cannot be made. Neither
can the settings of "AUDIO CHANNEL", "DIGITAL
OUTPUT", "LCPM (44.1kHz/48kHz)", "SOURCE DIRECT",
or "BASS ENHANCER" under "AUDIO SETUP".
The HDMI audio output is turned off if the digital output is set
to "OFF" at "PURE DIRECT", and the HDMI video and audio
output are both turned off if the video output is set to "OFF"
or if "ALL OFF" is set. (See Pages 47, 48.)
Also note that it will not be possible to select the setting of
digital output, when selecting "MULTI (NORMAL)" at "HDMI
AUDIO SETUP".
HDMI Input
connector
HDMI cable
(commercially available)
Audio
recording 2CH
format
2 channel
Dolby digital
PCM
DVD
video
2 channel
DTS
PCM
LPCM or P.PCM
X
(with CPPM)
DVD
Audio
2 channel
LPCM or P.PCM
(without CPPM) PCM
2 channel
Video CD
PCM
2 channel
CD
PCM
2 channel
MP3 CD
PCM
2 channel
WMA CD
PCM
Multi area X
Super
Audio Stereo area X
CD
2 channel
CD area
PCM
The multi-channel/stereo area sound of Super Audio CD is not
output.
The video and audio signals cannot be output when playing
DVD AUDIO with CPPM.
• When selecting MULTI (NORMAL) or MULTI (LPCM), the
DVD-3910 speaker settings under "AUDIO SETUP"become
invalid.
• When playing a Super Audio CD with an HDMI connection,
audio cannot be transferred beyond the CD area. Make an
analog connection for this.
• Among the devices that support HDMI, some devices can
control other devices via the HDMI connector; however, the
DVD-3910 cannot be controlled by another device vice the
HDMI connector.
• When using display equipment that is not supported by the
HDCP (content protection function), the image will not be
output properly. (See the compatibility table.)
• The audio signals from the HDMI connector (including the
sampling frequency and bit length) may be limited by the
equipment that is connected.
ENGLISH
Setting of HDMI
MULTI MULTI
(NORMAL) (LPCM)
Dolby digital Multi PCM
DTS Multi PCM
X X
Multi PCM Multi PCM
2 channel 2 channel
PCM PCM
2 channel 2 channel
PCM PCM
2 channel 2 channel
PCM PCM
2 channel 2 channel
PCM PCM
X X
X X
2 channel 2 channel
PCM PCM
19