Advertisement
Table of Contents
- 1 Section 1 - Familiarization
- 2 Section 2 - SAFETY MESSAGES and SYMBOLS
- 3 Section 3 - Operating
- 4 Cutting Height Adjustment
- 5 Safety Interlock System Checks
- 6 Section 4 - MAINTENANCE
- 7 Deck Removal
- 8 Section 5 - Adjustments
- 9 Traction Belt Replacement
- 10 Blade Brake/Electric Clutch Adjustment
- Download this manual
Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 1
MODELS
NZM19481KWV
NZM21521KWV
NZM25611KWV
NZM27611KH
MODEL
NUMBER
EXPLANATION
INI
;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP
: I 1111_1431 '
, I KWVl
J
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
19.0 - Engine Horse Power
21.0 -- Engine Horse Power
25.0 - Engine Horse Power
27.0 - Engine Horse Power
N - Model Designation
48 - 48" Mower Width
1 - Series Designation
Z - Zero Turning - Hydro Drive
52 - 52" Mower Width
KW - Kawasaki Engine
M - Mid Mount Mower
61 - 61" Mower Width
KH - Kohler Engine
V - Over Head Valve
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
SNAPPER McOo°ouo.
COPYRIGHT
© 2003
SNAPPER
PRODUCTS
INC
GA., 30253
U.S.A.
ALL RIGHTS
RESERVED
MANUAL No. 7-1762 (I.R. 11/25/03)
Advertisement
Table of Contents
Related Manuals for Snapper NZM19481KWV SERIES 1
Summarization of Contents
Section 1: Familiarization
1.1 Introduction to the Snapper Z-Rider
Overview of the manual's purpose and importance of reading safety instructions.
1.2 Nomenclature and Component Identification
Identification of essential parts and controls of the mower.
Section 2: Safety Messages and Symbols
DANGER and WARNING Safety Alerts
Explains critical safety messages and symbols for operator protection.
Motion Control Lever Operation
Details on operating the motion control levers for movement.
Parking Brake Lever Operation
Steps for engaging and disengaging the parking brake.
Control Panel and Ignition Switch Identification
Identifies controls on the panel and the ignition switch.
Section 3: Operating Instructions
Roll Release and Starting Engine
Instructions for rolling the machine and starting the engine safely.
Starting and Stopping Mower Blades
Procedures for engaging and disengaging the mower blades.
Stopping Engine and Parking Brake Usage
Steps for safely stopping the engine and using the parking brake.
Cutting Height Adjustment
How to adjust the mower deck cutting height.
Driving, Maneuvering, and Stopping the Machine
Instructions for operating motion controls and stopping the machine.
Safety Interlock System Checks
Procedures for verifying the functionality of safety interlock switches.
Section 4: Maintenance
Lubrication Procedures
Details on lubricating front wheel bearings, hydro pumps, and idler arms.
Pre-Operation and Annual Maintenance Tasks
Tasks to perform before operating and at the end of each season.
Fuel Filter Replacement
Step-by-step guide for replacing the fuel filter.
Mower Deck Removal Procedure
Instructions on how to safely remove the mower deck.
Section 5: Adjustments & Repair
Traction Belt Tension and Replacement
Adjusting and replacing the traction drive belt.
Blade Brake/Electric Clutch Adjustment
How to adjust the electric clutch for proper blade stopping.
Battery Removal, Installation, and Service
Procedures for handling and maintaining the mower battery.
Need help?
Do you have a question about the NZM19481KWV SERIES 1 and is the answer not in the manual?
Questions and answers