Snapper NZM19483KWV Safety Instructions And Operator's Manual
  1. Manuals
  2. Brands
  3. Snapper Manuals
  4. Lawn Mower
  5. NZM19483KWV
  6. Safety instructions and operator's manual

Snapper NZM19483KWV Safety Instructions And Operator's Manual

Mid mount z-rider zero turning hydro drive series 3
Hide thumbs Also See for NZM19483KWV:

Advertisement

Table of Contents

Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 3
MODELS
NZM19483KWV
NZM21523KWV
NZM25523KWV
NZM25613KWV
NZM27 613KH
MODEL
NUMBER
EXPLANATION
INI
;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP *
:1 I1 I 1_1431 :
I KWVl
I
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
19.0 - Engine Horse Power
21.0 -- Engine Horse Power
25.0 - Engine Horse Power
27.0 - Engine Horse Power
N - Model Designation
48 - 48" Mower Width
3 - Series Designation
Z - Zero Turning - Hydro Drive
52 - 52" Mower Width
KW - Kawasaki Engine
M - Mid Mount Mower
61 - 61" Mower Width
KH - Kohler Engine
V - Over Head Valve
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
NOTE: Specifications
are correct
at time of printing and are subject
to change without
notice.
* Actual sustained
equipment
horsepower will likely be lower due to operating limitations and environmental
factors.
SNAPPER.coonough
o., 3 o2 3
os.
COPYRIGHT
(_ 2005
SNAPPER
A DIVISION
OF SIIqPLIO]TY
_'TFG INC
ALL RIGHTS
RESERVED
MANUAL No. 7100080 (Rev. I, 9/20/2005)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NZM19483KWV and is the answer not in the manual?

Questions and answers

Related Manuals for Snapper NZM19483KWV

Summary of Contents for Snapper NZM19483KWV

  • Page 1 ENGINE HP * N - Model Designation Z - Zero Turning - Hydro Drive M - Mid Mount Mower Thank you for buying a SNAPPER Product! particular attention to the "IMPORTANT equipment can be dangerous accordance with the operating instructions and common sense!

  • Page 2: Section 2 - Safety Messages And Symbols

    Section 2 - SAFETY MESSAGES AND SYMBOLS KEEP AWAY FROM MOVING PARTS DANGER ! ROTATING PARTS I PARKING BRAKE LEVER OPERATION TO AVOID INJU RY OR DEATH - Read Operator's Manual Do not operate unless you am e fully tRained. - Keep all guard s,shields and othel satety devices in place and wol king.
  • Page 3 Section 2 - SAFETY MESSAGES AND SYMBOLS OFF/STOP START PULL SWITCH "UP" TO ENGAGE BLADES PUSH SWITCH "DOWN" HOUR METER DISENGAGE BLADES KEYSWITCH FAST SLOW CHOKE I CONTROL PANEL IDENTIFICATION CONTROL ENGINE SPEED CONTROL DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA I FUEL TANK SELECT STOP START...
  • Page 4 Section 2 - SAFETY MESSAGES AND SYMBOLS ROLL BARPROTECTIVESTRUCTUREDECALS CAUTION! SPRING LOADED MECHANISM...

  • Page 5: Pre-Start Checklist

    Section 3 - OPERATING PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.
  • Page 6 Perform the following interlock system checks periodically during the operating season. Contact your NEUTRAL LOCK authorized Snapper dealer if you have questions. POSITION DO NOT operate machine safety properly. remove any safety device.

  • Page 7: Section 4 - Maintenance

    Section 4 - MAINTENANCE WARN ING Allow engine to cool for at least ten minutes before performing service or maintenance. near fuel components when performing maintenance. perform maintenance near an open flame. spilled fuel before starting engine. engine indoors. 4.5 ANNUALLY (END OF EACH SEASON) (Continued from previous Page) 4,5,2.

  • Page 8: Neutral Position Adjustments

    Section 5 - ADJUSTMENTS DANGER Exercise EXTREME CAUTION adjustment, due to close proximity of moving parts. NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. levers to the center or neutral machine. IMPORTANT: Always return both motion control levers with...

  • Page 9: Mower Deck & Component Adjustments

    Section 5 - ADJUSTMENTS NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12, With motion control levers remaining neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod. Tie rod end bolt must align with the activation assembly.

  • Page 10: Traction Belt Replacement

    Section 5 - ADJUSTMENTS WARNING DO NOT attempt any maintenance, service with engine running. STOP engine. blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid allow sufficient time for all parts to cool. TRACTION BELT TENSION The traction drive belt tension does not require...

  • Page 11: Tracking Adjustment

    Section 5 - ADJUSTMENTS TRACKING ADJUSTMENT If the machine does not track straight Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSi before making this adjustment. 1.
  • Page 12 In the event that a spindle replacement, SNAPPER Spindles have been designed so that no special tools or presses are required. 1. Remove belt. Loosen blade nut and remove. Allow blade bolt, washer_ blade and four spacers to drop down out of the spindle Figure 5.19.

  • Page 13: Hydraulic System, Purging

    Section 5 - ADJUSTMENTS 5.12 HYDRAULIC SYSTEM, PURGING After replacing or repairing hydraulic system components, one or both of the wheel drives may not pull properly. This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perform the following procedure to purge the air from one or both of the hydraulic drive systems.

  • Page 14: Safety Instructions

    Safety Instructions MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 3 Snapper products are built using engines that meet or exceed all applicable date manufactured. The labels on those engines contain very important emissions safety warnings. Read, Understand, manual, and on the machine, engine and attachments.

This manual is also suitable for:

Nzm21523kwvNzm25523kwvNzm25613kwvNzm27 613khNzm27613kh

Table of Contents