Snapper NZM21521KWV SERIES 1 Safety Instructions & Operator's Manual

Snapper NZM21521KWV SERIES 1 Safety Instructions & Operator's Manual

Mid mount z-rider zero turning hydro drive series 1

Advertisement

Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 1
MODELS
NZM19481KWV
NZM21521KWV
NZM25611KWV
NZM27611KH
MODEL
NUMBER
EXPLANATION
INI
;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP
: I 1111_1431 '
, I KWVl
J
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
19.0 - Engine Horse Power
21.0 -- Engine Horse Power
25.0 - Engine Horse Power
27.0 - Engine Horse Power
N - Model Designation
48 - 48" Mower Width
1 - Series Designation
Z - Zero Turning - Hydro Drive
52 - 52" Mower Width
KW - Kawasaki Engine
M - Mid Mount Mower
61 - 61" Mower Width
KH - Kohler Engine
V - Over Head Valve
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
SNAPPER McOo°ouo.
COPYRIGHT
© 2003
SNAPPER
PRODUCTS
INC
GA., 30253
U.S.A.
ALL RIGHTS
RESERVED
MANUAL No. 7-1762 (I.R. 11/25/03)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NZM21521KWV SERIES 1 and is the answer not in the manual?

Questions and answers

Summarization of Contents

Section 1 - Familiarization
Introduction to the Snapper Z-Rider
Explains the purpose and scope of the operator's manual.
Machine Nomenclature and Controls
Identifies key components and controls of the machine.
Section 2 - Safety Messages and Symbols
Understanding Safety Symbols
Defines safety symbols like DANGER, WARNING, and CAUTION for user safety.
Motion Control and Brake Operation Safety
Details how to operate the motion control levers and parking brake safely.
Safe Starting and Stopping Procedures
Outlines the basic steps for starting, operating, and stopping the machine.
Control Panel Identification
Locates and identifies controls on the operator's control panel.
Rotating Blades Safety Warnings
Highlights critical safety warnings related to the mower's rotating blades.
Section 3 - Operating Instructions
Roll Release Operation
Procedure for moving the machine without the engine running.
Starting the Engine
Step-by-step guide for starting the engine from cold.
Stopping Engine and Blades
Instructions for safely stopping the engine and disengaging mower blades.
Starting Mower Blades
Procedure to engage the mower blades for operation.
Parking Brake Operation
Detailed steps for engaging and releasing the parking brake.
Cutting Height Adjustment
Guide on how to adjust the mower deck to desired cutting heights.
Driving the Machine
Operational instructions for moving the machine using motion controls.
Stopping the Machine
Steps for properly stopping the machine and securing it.
Safety Interlock System Checks
How to perform checks on the machine's safety interlock system.
Section 4 - Maintenance
Lubrication Points
Details on lubricating front wheel bearings, hydro pumps, and idler arms.
Pre-Operation Checks
Essential checks to perform before operating the mower.
Annual Maintenance Tasks
Recommended maintenance tasks for the end of each operating season.
Fuel Filter Service
Instructions for servicing and replacing the fuel filter.
Mower Deck Removal
Step-by-step guide for safely removing the mower deck.
Section 5 - Adjustments & Repair
Traction Belt Replacement
Procedure for replacing the traction drive belt.
Blade Brake/Electric Clutch Adjustment
Guide to adjusting the blade brake/electric clutch for proper stopping.
Battery Service and Installation
Procedures for battery removal, installation, and maintenance.

Table of Contents