Related Manuals for McIntosh MSS630
Summary of Contents for McIntosh MSS630
- Page 1 MSS530 and MSS630 Loudspeaker Systems McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 Owner’s Manual MSS530 MSS630 FAX: 607-724-0549...
-
Page 2: Table Of Contents
Phone: 607-723-3512 Fax: 607-723-3636 Customer Service If it is determined that your McIntosh product is in need of repair, you can return it to your Dealer. You can also return it to the McIntosh Laboratory Service Department. For as- sistance on factory repair return procedure, contact the McIntosh Service Department at: McIntosh Laboratory, Inc. -
Page 3: Important Safety Instructions
- this indicates a need for service. 14. When replacement parts are required, be sure the service technician has used replacement parts speci- fied by McIntosh or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. -
Page 4: Introduction
The McIntosh Woofer/Midrange and Tweeter Drivers offer extremely smooth frequency response, low distortion, high sensitivity and high power handling capability. When these Drivers are combined with other McIntosh Vehicle Compo- nents, you will enjoy sonically accurate music reproduction in your vehicle which meets McIntosh traditional standards of excellence. -
Page 5: Overall Dimensions
Front View of the MS20 Tweeter Driver 2.13" 5.4cm Front View of the MS530 Woofer/Midrange Driver Front View of the MS630 Woofer/Midrange Driver Introduction, Performance Features and Overall Dimensions Side View of the MS20 Tweeter Driver 0.88" 2.24cm Side View of the MS530 Woofer/Midrange Driver... -
Page 6: Installation
Midrange Drivers, Tweeters and Crossover Networks should be used in conjunction with McIntosh Subwoofers and McIntosh Electronics to achieve the best possible per- formance. McIntosh Subwoofers are designed to operate in the bass frequency range below 120Hz and need not be... - Page 7 Mounting the Crossover When selecting a Crossover mounting location, make sure there is adequate room for ventilation (there are openings on both sides of the Cross- Mounting Screw Locations over) and for making con- nections to it. Use the sup- plied screws for mounting the Crossover to the vehicle.
-
Page 8: How To Connect
Red wire to the (0) POSITIVE Terminal. Note: There are two additional Tweeter Positive Terminal 5. Connect the MINUS (-) OUTPUT of a McIntosh Power Amplifier to the Crossover Network MINUS INPUT Terminal and the PLUS (+) OUTPUT to the Crossover Network PLUS (+) INPUT Terminal. - Page 9 Environment. Connect the Tweeter Positive (Red) Cable to the -3dB or -6dB Positive Tweeter Output Terminal that produces the preferred sound. 5. Connect the MINUS (-) OUTPUT of a McIntosh Power Amplifier to the Crossover Network MINUS INPUT Terminal and the PLUS (+) OUTPUT to the Crossover Network PLUS (+) INPUT Terminal.
-
Page 10: Specifications
MSS530 System Specifications System Parameters Peak Power Continuous Power (EIA + H.P.) Frequency Response System Sensitivity Nominal Impedance (Znom) Crossover Frequency Low Pass Slope High Pass Slope MS530 Woofer/Midrange Mounting Dimensions Grille Overall (Diameter) Speaker + Grille Overall Depth Speaker Mounting Depth... -
Page 11: Packing Instructions
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a ship- ping carton or any of the interior part(s) are needed, please call or write Customer Service Repair Department of McIn- tosh Laboratory. - Page 12 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No. 040826...
Need help?
Do you have a question about the MSS630 and is the answer not in the manual?
Questions and answers