Related Manuals for McIntosh ML1
Summary of Contents for McIntosh ML1
- Page 1 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com Loudspeaker System Owner’s Manual...
- Page 2 The lightning flash with arrowhead, within an equilateral The exclamation point within an equilateral triangle is triangle, is intended to alert the user to the presence of intended to alert the user to the presence of important uninsulated “dangerous voltage” within the product’s en- operating and maintenance (servicing) instructions in closure that may be of sufficient magnitude to constitute the literature accompanying the appliance.
- Page 3 ML1 Stand ......6 connected to the ML1. performance from your equipment.
- Page 4 All together these advances in woofer design Two 4 inch lower midranges are used in the ML1 • Versatile Operation construction and materials produce the very to provide a symmetrical radiation pattern. This...
- Page 5 The Low Frequency Section of the System consists The Crossover Network used in the ML1 Loud- the design of the ML1 Loudspeaker System, a level of a newly designed 12 inch Woofer. speaker System is designed to ensure an even fre- of high performance.
- Page 6 ML1 Stand Dimensions The dedicated stand for the ML1 has been designed The following dimensions can assist in determining the best location for your ML1. to elevate and position the ML1 loudspeaker for optimum listening enjoyment and imaging. The stand comes with feet for use on hard floors, and spikes for use on carpet, etc.
- Page 7 ML1 Dimensions The following dimensions can assist in determining the best location for your ML1. 13 3/8” 34 cm 3 1/2” 17 1/2” 1 3/8” 8.9 cm 19.1 cm 3.5 cm 26 1/8” 66.4 cm 21 7/16” 18 3/4” 54.5 cm 47.6 cm...
- Page 8 When connecting the loudspeaker hookup cables to Caution: It is very important to install the four feet on 6. Repeat steps 1 and 2 on the ML1 Stand shipping the bottom of the stand. This will greatly prevent the amplifier output terminals please follow the steps carton and remove the stand from the carton.
- Page 9 Installation Loudspeaker Placement Loudspeaker placement in a room can greatly affect performance. The ML1 loudspeaker is designed for both Music and Home Theater Systems. The optimal method for selecting speaker locations includes the use of a real time spectrum analyzer operated by an experienced system installer.
- Page 10 How to Connect Using One Amplifier Caution: The AC Power Cord should not be connected Select from the following options to connect the ML1: to the Amplifier until after the Loudspeaker Banana Plugs: Spade Lug or Wire Connections: Connections have been made. Failure to observe 2.
- Page 11 Connection Diagram (one amplifier) DISABLED...
- Page 12 5. Referring to figure 4, connect larger the wire size: the Loudspeaker hookup cables with banana plugs into the hole at the end of the ML1 LOW Loudspeaker Cable Distance vs Wire Gauge Guide Negative (-) and Positive (+) Input Terminals.
- Page 13 Connection Diagram (two amplifiers) Note: Jumpers must be removed for this arrangement. DISABLED DISABLED...
- Page 14 Customer Service 8 ohms Nominal Width is 15 inches (38.1cm) Department of McIntosh Laboratory. Refer to page Frequency Response Height is 26 1/8 inches (66.4m) 3. Please see the packing part lists on the following...
- Page 15 ML1 Packing Parts List ML1 Stand Packing Parts List Part Number Description Part Number Description 034714 Shipping Carton Speaker Stand 034701 Shipping Carton only 034712 Foam End Cap Stand 034702 Foam Tray Top/Bottom 034718 Poly Bag (Speaker) 034703 Foam Support Center...
- Page 16 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 24120200...
Need help?
Do you have a question about the ML1 and is the answer not in the manual?
Questions and answers