Related Manuals for McIntosh XRT1K
Summary of Contents for McIntosh XRT1K
-
Page 1: Loudspeaker System
Loudspeaker System XRT1K Owner’s Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549... -
Page 2: Important Safety Instructions
WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. -
Page 3: Table Of Contents
Phone: 607-723-1545 Fax: 607-724-0549 Customer Service If it is determined that your McIntosh product is in need of repair, you can return it to your Dealer. You can also return it to the McIntosh Laboratory Service Department. For assistance on factory repair return procedure, contact the McIntosh Service Department at: McIntosh Laboratory, Inc. -
Page 4: Introduction
Introduction McIntosh Acoustic Engineers have further refined the con- cept of line source column in the XRT1K Loudspeaker to provide superior sound reproduction in a full range system. It uses the same acoustic technology found in the famous XRT2K Column Loudspeakers. The technology has been... -
Page 5: Introduction And Performance Features
Loudspeaker. • High Power Handling The Loudspeaker Elements and Crossover Components of the XRT1K are all chosen for use with powerful amplifiers up to 1,200 watts. • Superior Imaging Locating the Tweeters between the two rows of Midranges generates a symmetrical horizontal polar response for superior imaging. -
Page 6: Dimensions
Dimensions The following dimensions can assist in determining the best location for your XRT1K Loudspeaker System. Front View of the XRT1K Loudspeaker System 11" 27.9cm " 201.9cm 2" 5.1cm " 36.8cm Side View of the XRT1K Loudspeaker System 31.1cm "... -
Page 7: Dimensions
Front View of the XRT1K Loudspeaker System " -5/16 18.6cm " -1/2 14.0cm " -11/16 9.4cm " -7/32 5.6cm " -3/4 4.4cm " -7/8 50.5cm " -5/8 19.4cm " -7/8 40.3cm Note: The base is an integral part " -9/32 66.8cm... -
Page 8: Installation
XRT1K Loudspeaker System and any associated audio equipment. CAUTION: This Loudspeaker weighs 168 pounds (76.2 kgs). 1. Orient the XRT1K shipping carton with the arrows on the outside of the carton pointing upward. 2. Remove the banding material from the shipping car- ton and lift off the top of the shipping carton and set it aside. -
Page 9: How To Connect Using A Single Amplifier
Refer to figures 12, 13 & 14. Figure 12 Figure 13 2. Connect a Loudspeaker cable from the XRT1K LOW Frequency COM (-) Binding Post to the (-) Binding Post of the Power Amplifier. Notes: 1. It is important to maintain the correct polarity at both ends of the Loudspeaker cables. -
Page 10: How To Connect Using Two Amplifiers
3. Remove the metal jumper between the Loudspeaker LOW Frequency 8Ω (+) Binding Post and MID Fre- quency 8Ω (+) Binding Post. 4. Connect a Loudspeaker cable from the XRT1K LOW Frequency COM (-) Binding Post to the (-) Binding Post of the Power Amplifier number one. - Page 11 How to Connect using a two Amplifiers McIntosh Power Amplifier number two Jumper Jumper...
-
Page 12: How To Connect Using Three Amplifiers
Figure 13 2. Remove all four metal jumpers between Loudspeaker Binding Posts. 4. Connect a Loudspeaker cable from the XRT1K LOW Frequency COM (-) Binding Post to the (-) Binding Post of the Power Amplifier number one. Note: It is important to maintain the correct polarity at both ends of the Loudspeaker cables. - Page 13 How to Connect using a three Amplifiers McIntosh Power Amplifier number three McIntosh Power Amplifier number two...
-
Page 14: General Specifications
Specifications System Driver Complement Two 10 inch LD/HP Woofers Forty-four 2 inch Titanium Inverted Dome Midranges Twenty-eight 3/4 inch Titanium Dome Tweeters Impedance 8 ohms Nominal Frequency Response 16Hz - 45kHz Sensitivity 88dB (2.8V/1m equivalent) Crossover Frequencies 250Hz 2,000Hz Power Handling 1,200 Watts Maximum General Specifications Finish Enclosures... -
Page 15: Packing Instruction
If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Labo- ratory. Please see the Part List for the correct part numbers. - Page 16 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04101401...
Need help?
Do you have a question about the XRT1K and is the answer not in the manual?
Questions and answers