Advertisement
Quick Links
BEFORE YOU BEGIN:
To avoid any confusion with your new
shed build, we strongly suggest that you
unpack and identify each part before you
begin to put it together.
ASSEMBLY
INSTRUCTIONS
YOU SHOULD HAVE TWO PACKAGES:
• 1 cardboard package
• 1 channel pack
TOOLS SUPPLIED:
• 1 riveter
• 3.3mm double ended drillbit
TOOLS REQUIRED:
• Battery or electric drill (drill bits supplied)
• Tape measure
• Ladder
• Non-slip gloves, good shoes and goggles
• A set of helping hands
SCAN TO
WATCH OUR
ASSEMBLY VIDEO
HERE
Some parts have sharp edges and should be handled
very carefully. We recommend the use of protective
gloves and footwear when assembling.
DO NOT attempt to erect this shed in windy weather.
All dimensions are approximate.
3030mm wide x 3315mm deep x 1830mm - 2120mm high
25
EST.
1974
YEAR
WARRANTY
GABLE ROOF SHED
WAS PROUDLY
this code for any
correspondence back
GM3033
THIS SHED
PACKED BY:
Please quote
to the supplier
CALL 0508 454 873
for an installer near you
Advertisement
Related Manuals for GARDEN MASTER GABLE GM3033
Summary of Contents for GARDEN MASTER GABLE GM3033
- Page 1 GM3033 GABLE ROOF SHED 3030mm wide x 3315mm deep x 1830mm - 2120mm high BEFORE YOU BEGIN: THIS SHED WAS PROUDLY To avoid any confusion with your new PACKED BY: shed build, we strongly suggest that you unpack and identify each part before you Please quote this code for any begin to put it together.
- Page 2 COMPONENTS CHECKLIST Please check the parts carefully and advise immediately if any are damaged or missing. 4 x 1830mm Sheets for back 8 x 1770mm sheets for roof 8 x sloping sheets & 1 x 780mm wide sheet with 1 x 1830mm Sheets for front 2 x gable cut sheets for ends door jamb attached Door pre-hinged to 700mm...
- Page 3 B Drill through to the underside. Rivet top and underside. FITTING CHANNELS CHANNELS WITH CUTOUTS GARDEN MASTER TIP The cutouts go to the inside of the panel to The higher side of the channel goes to the To hinge the door on the opposite side, inside of the shed.
- Page 4 Make sure you put at least 1 rivet per sheet up through the underside of the channel into the pan of the sheet. GARDEN MASTER TIP SCAN TO WATCH OUR ASSEMBLY VIDEO Put extra rivets in for high wind areas, HERE particularly on the underside.
- Page 5 STEP 4: END WALLS YOU WILL NEED: 8 x sloping sheets & Join 5 sheets together to create a gable end wall as shown. 2 x gable cut sheets for end Make a cut in the flanges only at (1665mm) the centre of the 2 x 3285mm channels for bottom &...
- Page 6 FIT THE DOOR BRACES AND INSTALL SHED Fit the door braces, if not already done so. Check that all filings/swarf is removed. IMPORTANT GARDEN MASTER HINTS & TIPS DIAGRAM 9 IMPORTANT:...
- Page 7 STEP 7: COMPLETE YOUR SHED RECESSED CONCRETE FLOOR PLAN FOR SPECIALLY POURED CONCRETE FLOORS: SPECIFICATIONS Every shed must have some type of foundation between it and the ground. You can pour a concrete floor and use recessed floor clamps, use an existing concrete base with flat floor clamps or purchase a kitset wooden floor from your shed dealer. 20MM - 25MM APPROX 25MM RECESS 25MM...
- Page 8 What did you like best about your garden shed purchase? Are there any parts of our service that you think we could improve upon? THANKS FOR YOUR HELP! GARDEN MASTER SHED OPTIONAL EXTRAS 1. SHELF BRACKETS 2. TOOL RACKS 3. FLOORS 4.
Need help?
Do you have a question about the GABLE GM3033 and is the answer not in the manual?
Questions and answers