GARDEN MASTER GM1508 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. GARDEN MASTER Manuals
  4. Outdoor Storage
  5. GM1508
  6. Assembly instructions manual

GARDEN MASTER GM1508 Assembly Instructions Manual

Sloping roof shed
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
BEFORE YOU BEGIN:
To avoid any confusion with your new
shed build, we strongly suggest that you
unpack and identify each part before you
begin to put it together.
ASSEMBLY
INSTRUCTIONS
YOU SHOULD HAVE ONE PACKAGE:
• 1 cardboard package
TOOLS SUPPLIED:
• 1 riveter
• 3.3mm double ended drillbit
TOOLS REQUIRED:
• Battery or electric drill (drill bits supplied)
• Tape measure
• Ladder
• Non-slip gloves, good shoes and goggles
• A set of helping hands
SCAN TO
WATCH OUR
ASSEMBLY VIDEO
HERE
Some parts have sharp edges and should be handled
very carefully. We recommend the use of protective
gloves and footwear when assembling.
DO NOT attempt to erect this shed in windy weather.
All dimensions are approximate.
SLOPING ROOF SHED
1530mm wide x 780mm deep x 1830mm - 1770mm high
25
EST.
1974
YEAR
WARRANTY
GM1508
THIS SHED
WAS PROUDLY
PACKED BY:
Please quote
this code for any
correspondence back
to the supplier
CALL 0508 454 873
for an installer near you

Advertisement

Table of Contents
loading

Related Manuals for GARDEN MASTER GM1508

Summary of Contents for GARDEN MASTER GM1508

  • Page 1 GM1508 SLOPING ROOF SHED 1530mm wide x 780mm deep x 1830mm - 1770mm high BEFORE YOU BEGIN: THIS SHED WAS PROUDLY To avoid any confusion with your new PACKED BY: shed build, we strongly suggest that you unpack and identify each part before you...

  • Page 2: Components Checklist

    COMPONENTS CHECKLIST Please check the parts carefully and advise immediately if any are damaged or missing. 2 x 1770mm sheets for the back 2 x 1830mm - 1770mm sloping sheets 2 x 980mm sheets for the roof (side walls 1 left, 1 right) Door pre-hinged to 715mm sheet 4 x 780mm channels for end walls 4 x 1515mm channels with ends cut...

  • Page 3: Front Wall

    ASSEMBLY VIDEO HERE FITTING CHANNELS CHANNELS WITH CUTOUTS GARDEN MASTER TIP The cutouts go to the inside of the panel to The higher side of the channel goes to the To hinge the door on the opposite side, inside of the shed. It is very important to...
  • Page 4 Rivet the channels through the end ribs and every 2nd rib between. Make sure you put at least 1 rivet per sheet up through the underside of the channel into the pan of the sheet. GARDEN MASTER TIP SCAN TO WATCH OUR...
  • Page 5 STEP 4: END WALLS YOU WILL NEED: 2 x 1830mm - 1770mm sheets (1 per side) Cap 1 sheet with 780mm channels. 4 x 780mm channels (2 per side) Rivet the channels at the corners and every 2nd rib in between. 2 rivets up underneath through channel into pan of sheet.

  • Page 6: Installation

    FIT THE DOOR BRACES AND INSTALL SHED Fit the door braces, if not already done so. Check that all filings/swarf is removed. IMPORTANT GARDEN MASTER HINTS & TIPS DIAGRAM 9 IMPORTANT:...

  • Page 7: Specifications

    INTERNAL DIMENSIONS RECESSED FLOOR CLAMPS For poured floors with a recess around the perimeter. Available from your shed dealer. INTERNAL DIMENSIONS FOR THE GM1508: FLAT FLOOR CLAMPS For existing concrete only. Water can seep underneath. 1485MM X 735MM Available from your shed dealer.
  • Page 8 What did you like best about your garden shed purchase? Are there any parts of our service that you think we could improve upon? THANKS FOR YOUR HELP! GARDEN MASTER SHED OPTIONAL EXTRAS 1. SHELF BRACKETS 2. TOOL RACKS 3. FLOORS 4.

Table of Contents