Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hoteche P805204A
Summary of Contents for Hoteche P805204A
- Page 1 SINCE 1995 P805204A 15A(2000W) 255MM(10'') MITER SAW WITH LASER Int rtek...
-
Page 2: Table Of Contents
CONTENTS • Know your product • Specifications • Intended use • Not intended use • General safety instructions • Safety rules for mitre saws • Residual risks • Operating instructions • Maintenance • Service • Guarantee Danger! - Read the operating instructions to reduce the risk of injury Caution! Wear ear-muffs. -
Page 3: Know Your Product
KNOW YOUR PRODUCT PARTS LIST 1. Saw arm 16. Table insert 2. Release knob 17. Switch trigger 3. Operating handle 18. Mitre lock knob 19. Mitre latch 4. Upper fixed blade guard 5. “G” Clamp 20. Spindle lock 21. Slide bars 6. -
Page 4: Specifications
• SPECIFICATIONS Mitre cut at 0° x 45° : 315 x 40 mm • Bevel cut at 45° x 0° : 215x 90 mm • Compound mitre cut at 45° x 45° : 215 x 40 mm TECHNICAL DATA • •... - Page 5 (corded) power tool or battery-operated (cordless) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power tool. power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your Save all warnings and instructions for future finger on the switch or energizing power tools that have the switch on invites accidents.
- Page 6 Supporting the workpiece “cross handed” i.e. holding and in the manner intended for the particular type of power tool, taking into account the working the workpiece to the right of the saw blade with your conditions and the work to be performed. Use of left hand or vice versa is very dangerous.
-
Page 7: Residual Risks
n) The cut-off piece must not be jammed or operation! This field may under some circumstances interfere with active or passive medical implants! To pressed by any means against the spinning saw reduce the risk of serious or fatal injury, we recommend blade. -
Page 8: Bench Mounting
saw from rotating. Depress and hold the spindle lock WARNING! button while installing, changing, or removing the blade. To prevent the accidental starting that could cause ROTATING LOWER BLADE GUARD possible serous personal injury, ALWAYS assemble all The rotating lower blade guard (6) provides protection parts to you saw BEFORE connecting it to the power from both sides of the blade. -
Page 9: Setting The Fence Square With The Table
Retighten the screw. 11. Fit the new blade onto the spindle taking care that the inner blade washer sits behind the blade. 14. Retighten the bevel lock (10) and the lock nut securing the 0° bevel adjustment screw (27). 12. Replace the outer blade washer. SETTING THE FENCE SQUARE WITH THE TABLE 13. -
Page 10: Bevel Cut
to stop rotating before raising the blade out of the Do not remove a cut-off piece on the right-hand side of workpiece. Wait until the blade stops before removing the blade using your left hand. the workpiece. A compound mitre cut involves using a mitre angle and a BEVEL CUT bevel angle at the same time. -
Page 11: Maintenance
tighten the lock nut to secured the stop knob. Tool service must be performed only by qualified repair • personnel. Service or maintenance performed by 4. Recheck the blade depth by moving the cutting head unqualified personnel could result in a risk of injury. front to back through the full motion of typical cut along the control arm. - Page 13 Part name EN Spec & Material Part name EN Spec & Material Screw M5X35 80 Hex bolt M10X100 Washer Φ5 81 Bevel locker PA6-GF30 Tapping screw ST4.2X13 82 Washer Φ22XΦ10.3X3 Upper handle PA6-GF30 83 Bevel Scale Spring 65Mn 84 Linear bearing Φ40XΦ25X35 Switch Trigger assembly PA6-GF30...
Need help?
Do you have a question about the P805204A and is the answer not in the manual?
Questions and answers