Subscribe to Our Youtube Channel
Related Manuals for Advantech FPM-S Series
Summary of Contents for Advantech FPM-S Series
- Page 1 Startup Manual FPM-S Series: FPM-S15W FPM-S18W FPM-S21W Interchangeable Slim Bezel Display Modules 製造商: 研華股份有限公司 地址: 台北市內湖區陽光街365巷33號 電話: 02-27927818...
- Page 2 The documentation and the software included with this product are copyrighted 2025 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
-
Page 3: Table Of Contents
Content Chapter 1 Installation .......... 1 Confirm Your TPC and FPM Products ............. 2 Installing FPM-S15W with TPC System ..........3 1.2.1 Positioning Pillars of FPM-S15W ..........3 Figure 1.1 FPM-S15W Rear View and Positioning Pillars ..3 1.2.2 Secure TPC with FPM-S15W ..........3 Figure 1.2 Installing TPC-B300 onto the FPM-S15W .... -
Page 4: Installation
Chapter Installation FPM-S Startup Manual... -
Page 5: Confirm Your Tpc And Fpm Products
The FPM-S display modules are equipped with positioning pillars to simplify in- stallation, enabling users to confirm the correct placement before securing with a screwdriver. However, due to size differences within the FPM-S series, some models may not be compatible with certain TPC models. Therefore, it is essential to ensure you have selected the correct TPC product. -
Page 6: Installing Fpm-S15W With Tpc System
Installing FPM-S15W with TPC System 1.2.1 Positioning Pillars of FPM-S15W The four positioning pillars, which are crucial for ensuring correct installation, are clearly highlighted by the red boxes in the diagram below (Figure 1.1). Figure 1.1 FPM-S15W Rear View and Positioning Pillars 1.2.2 Secure TPC with FPM-S15W Use the screws from the accessory box to firmly attach your FPM-S and TPC... - Page 7 Figure 1.3 Installing TPC-B510 onto the FPM-S15W Figure 1.4 Installing TPC-B520 onto the FPM-S15W FPM-S Startup Manual...
-
Page 8: Installing Fpm-S18W/S21W With Tpc System
Installing FPM-S18W/S21W with TPC System 1.3.1 Positioning Pillars of FPM-S18W/S21W If the FPM-S you purchased is larger than 15" and is paired with TPC products from the TPC-B300, TPC-B510, or TPC-B520 series, the default positioning pil- lars of the FPM-S do not need to be changed. However, if you are switching from the TPC-B610 series to another series, you must verify whether the positioning pillar locations align with those marked by the red boxes in the diagram below (Figure 1.5). -
Page 9: Secure Tpc With Fpm-S18W/S21W
1.3.2 Secure TPC with FPM-S18W/S21W Use the screws from the accessory box to firmly attach your FPM-S and TPC products. The following diagrams (Figure 1.7, Figure 1.8, Figure 1.9 & Figure 1.10) illustrate how to secure the FPM-S18W/S21W with various models of the TPC series. - Page 10 Figure 1.9 Installing TPC-B520 onto FPM-S18W/S21W Figure 1.10 Installing TPC-B610 onto FPM-S18W/S21W FPM-S Startup Manual...
-
Page 11: Led Status Indicator
Chapter LED Status Indicator FPM-S Startup Manual... -
Page 12: Led Status Indicator On Fpm-S Display
LED Status Indicator on FPM-S Display Indicator Default Status (ErP Enable) Status 2 (ErP Disable) Green Normal Powered-On State Normal Powered-On State Orange Sleep (S3) / Hibernate (S4) Sleep (S3) / Hibernate (S4) / Shutdown(S5) No Light Shutdown(S5)/Power Off Power Off FPM-S Startup Manual... -
Page 13: Panel Mounting
Chapter Panel Mounting FPM-S Startup Manual... -
Page 14: Panel Mounting
Panel Mounting There is an adhesive waterproof gasket on the front bezel of the FPM-S display module. Make sure the waterproof gasket is in position before in- stalling it into the panel opening. Install the FPM+TPC into the panel opening. The suggested mounting panel thickness is less than 6 mm (0.236 in). - Page 15 Ensure the brackets remain in place, then tighten the screws by turning them clockwise to a torque setting of 5 kgf-cm. This action will press the mounting panel firmly in place, ensuring a stable installation. Figure 3.3 Panel Mounting – Fixing FPM-S Startup Manual...
-
Page 16: Dimensions
Dimensions 3.2.1 FPM-S15W Panel Cutout Dimensions: 386.8 x 236.2mm, corner=R6mm (±0.5mm) FPM-S Startup Manual... -
Page 17: Fpm-S18W
3.2.2 FPM-S18W Panel Cutout Dimensions: 455.6 x 276.6mm, corner=R6mm (±0.5mm) FPM-S Startup Manual... -
Page 18: Fpm-S21W
3.2.3 FPM-S21W Panel Cutout Dimensions: 520.7 x 312.4mm, corner=R6mm (±0.5mm) FPM-S Startup Manual... - Page 19 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2025 FPM-S Startup Manual...
Need help?
Do you have a question about the FPM-S Series and is the answer not in the manual?
Questions and answers