Omnitron Systems OmniConverter 10GPoE+/S User Manual

Multi-gigabit/multi-rate 10m, 100m, 1g, 2.5g, 5g, 10g poe media converters

Advertisement

OmniConverter
10GPoE+/S and 10GPoEBT/S
Multi-Gigabit/Multi-Rate
10M, 100M, 1G, 2.5G, 5G, 10G
PoE Media Converters
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
®
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
TM
TM
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
®
®
the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
material and workmanship for a period of two (2) years from the date of shipment.
A lifetime warranty may be obtained by the original purchaser by registering this
product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
TM
®
, OST
TM
Page 2
,
®
and
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniConverter 10GPoE+/S and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems OmniConverter 10GPoE+/S

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Product Overview

    Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ The OmniConverter 10GPoE+/S and 10GPoEBT/S are unmanaged 10G Ethernet EU, for electrical and electronic equipment sold in the EU after July 2019. Such...
  • Page 3 SW1: Mode Of Operation - “Normal / Directed” 1) Configure DIP-switches DIP-switches are located on the side of the module. The DIP-switches are used to This DIP-switch is only supported on models with 2 RJ-45 ports. This DIP- configure modes of operation, networking features and PoE settings. switch is reserved for future use on all 1 RJ-45 port models.
  • Page 4: Installing The Module

    SW4: PoE Power Port 2 - “On / Off” 2) Installing the Module When this DIP-switch is in the factory default DOWN “On” position, PoE power on Wall Mounting Port 2 is turned on. When this DIP-switch is in the UP “Off” position, PoE power on The wall mounting height of the module should be less than or equal to 2 meters Port 2 is turned off and does not perform any PoE functions.
  • Page 5 Appropriate overloading protection should be provided on the DC power source Route the power cord through the provided strain relief for additional support and connect the barrel or DIN connector (depending on the model) at the end of the wire outlets utilized.
  • Page 6: Connect Cables

    4) Connect Cables Insert the SFP/SFP+ transceiver into the SFP receptacle on the front of the module. Refer to the SFP or SFP+ data sheets for supported 1G and 10G transceivers. The data sheets are available on the XFP, SFP+ and SFP Transceiver product page at: www.omnitron-systems.com NOTE: The release latch of the SFP fiber transceiver must be in the closed...
  • Page 7: Verify Operation

    5) Verify Operation RJ-45 Ports LED Indicators Verify the module is operational by viewing the LED indicators. Legend Indicator Description Port Not Linked Power LED Indicators Legend Indicator Description Green - ON Port linked at the speed indicated by the Rate LED Link Unit not powered Port is transmitting or receiving data at the rate indicated...
  • Page 8: Specifications

    Specifications OmniConverter 10GPoEBT/S Multi-gigabit/multi-rate copper to Multi-gigabit/multi-rate copper to Description OmniConverter 10GPoE+/S 1/10G SFP Media Converter with 1/10G SFP Media Converter with Description Multi-gigabit/mult-rate copper to 1/10G SFP Media Converter with IEEE 802.3bt 60W IEEE 802.3bt 100W IEEE 802.3at 15/30W IEEE 802.3, 802.3bz,...
  • Page 9 Mechanical Safety: UL 62368-1*, UL 60950-1*, IEC 62368-1*, IEC 60950-1*, EN 62368-1*, 1 RJ-45 Port EN 60950-1*, 9191-01-11 CAN/CSA C22.2 No. 62368-1-14*, CAN/CSA C22.2 No. 60950-1*, 9192B-0-11 CE Mark, UKCA 9194B-0-11 EMC: EN 55032/24 CE Emissions/Immunity, UKCA EMI: CISPR 32, FCC 47 Part 15 Subpart B Class A Regulatory Compliances EMS:...
  • Page 10 Intentionally left blank Page 19 Page 20...

This manual is also suitable for:

Omniconverter 10gpoebt/s

Table of Contents