Dell AW2524HB Service Manual
Dell AW2524HB Service Manual

Dell AW2524HB Service Manual

Advertisement

Quick Links

Service Manual–AW2524HB
Version: 02
Date:2023/06/27
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AW2524HB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dell AW2524HB

  • Page 1 Service Manual–AW2524HB Version: 02 Date:2023/06/27 - 1 -...
  • Page 2: Table Of Contents

    Content Index 1. General Safety Instructions ..................3 1.1 SAFETY: General Safety ..................3 1.2 SAFETY: General Power Safety ................5 2. Exploded view diagram with list of items ..............6 3. Wiring connectivity diagram ..................8 4. How to connect and disconnect power cable/ connectivity cable ......9 5.
  • Page 3: General Safety Instructions

    IMPORTANT NOTICE FOR USE IN HEALTHCARE ENVIRONMENTS: Dell products are not medical devices and are not listed under UL or IEC 60601 (or equivalent). As a result, they must not be used within 6 feet of a patient or in a manner that directly or indirectly contacts a patient 1.1 SAFETY: General Safety...
  • Page 4: Protecting Against Electrostatic Discharge

    When operating your equipment:  Do not use your equipment in a wet environment, for example, near a bath tub, sink, or swimming pool or in a wet basement. Do not use AC powered equipment during an electrical storm. Battery powered devices may ...
  • Page 5: Safety: General Power Safety

    If your equipment uses an AC adapter:  Use only the Dell provided AC adapter approved for use with this device. Use of another AC adapter may cause a fire or explosion.  NOTE: Refer to your system rating label for information on the proper adapter model approved for use with your device.
  • Page 6: Exploded View Diagram With List Of Items

    2. Exploded view diagram with list of items - 6 -...
  • Page 7 USB 3.2 Gen 1 (5 Gbps) upstream cable See “NOTE" NOTE: For replacement of power cord, connectivity cable and external power supply (if applicable), contact Dell: 1. Go to https://www.dell.com/support. 2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom-right corner of the page.
  • Page 8: Wiring Connectivity Diagram

    3. Wiring connectivity diagram FFC 6 Wire 2 Wire 4 Wire 3 FFC 5 FFC 4 FFC 3 Wire 1 FFC 2 FFC 1 - 8 -...
  • Page 9: How To Connect And Disconnect Power Cable/ Connectivity Cable

    4. How to connect and disconnect power cable/ connectivity cable WARNING: To change power cable/ connectivity cable, switch off power before unplugging the cable and replugging in required cable. Connect/ disconnecting the DisplayPort (DisplayPort to DisplayPort) cable and Power cable Connecting/ disconnecting the USB Type-C cable and Power cable - 9 -...
  • Page 10: Disassembly And Assembly Procedures

    5. Disassembly and Assembly Procedures NOTE: This “Disassembly and Assembly Procedures” is for EMEA only, not for other regions. Please note that Dell will deem warranty void if any disassembly is done on the monitors. 5.1 Disassembly SOP Preparation before disassembly 1.
  • Page 11: Operation

    Item Picture Operation Tool Notes 1. Unlock 4 screws on Philips- Rear Cover head Disassembly screwdriver Sequence 2. Use hands or scraper bar to (Screw disassemble Rear Torque: 8.0- Cover from the 10.0 kgf)) monitor. 2. Scraper Notice the disassembly order: Left Side=>...
  • Page 12 Item Picture Operation Tool Notes 1. Disconnect “I/F BD to Light Sensor BD FFC” from I/F BD I/F BD to Light Sensor BD FFC (FFC 5P P1 60MM LIGHTSOR) 1. Tear off 6 tapes Philips- from “MCU BD to head Panel wire”...
  • Page 13 Item Picture Operation Tool Notes 1. Tear off an acetate tape from EDP cable 2. Tear off a conductive tape and yellow tape from EDP cable 3. Disconnect EDP cable from Panel 4. Take off Main SHD from Panel 1. Disassemble Safety Philips- Mylar from Main head...
  • Page 14 Item Picture Operation Tool Notes 5. Disconnect “I/F BD to MCU BD FFC” from MCU BD 6. Disassemble MCU BD from Main SHD 7. Disconnect “SPS BD to I/F BD & MCU BD wire” from MCU BD 8. Disassemble I/F BD from Main SHD 9.
  • Page 15 Item Picture Operation Tool Notes 11. Tear off a tape from Do not touch “SPS BD to I/F BD & MCU BD wire” component without 12. Disassemble SPS wearing BD from Main SHD insulating gloves when disassemblin g and assembling Power BD 13.
  • Page 16 Item Picture Operation Tool Notes 1. Unlock 4 Heat Sink Philips- Screws head screwdriver Screw Torque- Heat Sink: 4-4.5 kgf) 2. Unlock 4 captive (Screw screws to Torque- disassemble G- Captive Sync module, Heat Screw: Sink Module and kgf) SHEET STIFFENER 3.
  • Page 17: Assembly Sop

    5.2 Assembly SOP Preparation before assembly 1. Clean the room for work 2. Identify the area for material 3. Prepare the implement, equipment, materials as bellow: 1) Working table 2) Philips-head screwdriver 3) Gloves 4) Cleaning cloth 5) ESD protection Item Picture Operation...
  • Page 18 Item Picture Operation Tool Notes 1. Assemble G- Philips-head SYNC Module screwdriver with I/F BD and fix it by screw*4 (Screw Torque: 4-4.5 kgf) 2. Insert “HEAT SINK Fan Cable” into I/F BD 1. Insert “SPS BD to Do not touch I/F BD &...
  • Page 19 Item Picture Operation Tool Notes 4. Insert “I/F BD to MCU BD FFC” to I/F BD 5. Insert “SPS BD to I/F BD & MCU BD wire” into I/F 6. Assemble I/F BD to Main SHD 7. Insert “SPS BD to I/F BD &...
  • Page 20 Item Picture Operation Tool Notes 10. Lock PCBA by Philips-head screws*11 screwdriver 11. Insert EDP cable (Screw to I/F BD Torque: 7.5- 9.5 kgf) 12. Paste an adhesive tape to fix EDP cable 13. Assemble Safety Mylar to Main SHD to cover SPS BD 1.
  • Page 21 Item Picture Operation Tool Notes 4. Paste an acetate tape to fix EDP cable 5. Place Main SHD on Panel 1. Insert “LENS BD Key BD FFC FFC” to “MCU (FFC 4P P1 520MM STICK) BD” 2. Insert “KEY BD FFC”...
  • Page 22 Item Picture Operation Tool Notes 1. Insert “I/F BD to Light Sensor BD FFC” to I/F BD I/F BD to Light Sensor BD FFC (FFC 5P P1 60MM LIGHTSOR) 1. Insert “MCU BD MCU BD to USB BD FFC (4P) MCU BD to USB BD FFC (30P) to USB BD FFC (FFC USB3 30/30 P0.5 105MM)
  • Page 23 Item Picture Operation Tool Notes 1. Follow the Philips-head sequence to screwdriver Assembly assemble Rear Sequence Cover with (Screw Middle Frame Torque: 8.0- 10.0 kgf) 2. Lock 4 RC screws 1. Assemble Stand a. Align and place the stand riser on the stand base b.
  • Page 24: Trouble Shooting Instructions

    6. Trouble shooting instructions - 24 -...
  • Page 25 - 25 -...
  • Page 26 - 26 -...
  • Page 27 - 27 -...
  • Page 28 - 28 -...
  • Page 29 - 29 -...
  • Page 30 - 30 -...
  • Page 31 - 31 -...
  • Page 32 - 32 -...
  • Page 33 - 33 -...

Table of Contents