ANTAIRA INJ-C201G-bt-100-24 Series Quick Installation Manual

Antaira Technologies
INJ-C201G-bt-100-24 Series
Industrial Gigabit Enhanced PoE++ Injector –
1*10/100/1000Base-T(X) with PoE-PSE (90W/Port) +
1*10/100/1000Base-T(X), Booster Version, 9~55VDC, EOT:
-40°C to 75°C
Quick Installation Guide
Version 1.0
(November 2021)
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
Package Check List
The package contains the following items:
1 – Quick installation guide

1 – INJ-C201G-bt-100-24-T

1 – Wall mounting bracket set with screws

1 – DC cable –18 AWG & DC jack 5.5 x 2.1mm

Front Panel Layout
Power LED
PoE LED
PoE Load LED
10/100/1000Base-T(X)
PoE++ Copper Port
10/100/1000Base-T(X)
Copper Port
Top Panel View
INJ-C201G-bt-100-24-T top panel is equipped with one 4-pin
removal terminal block connector for dual DC power inputs
(9~55VDC) and one 2-pin removal terminal block for fault alarm.
2-pin Terminal Block
Product Overview
System Interface/Performance
10/100/1000BaseT Power over Ethernet Injector

IEEE 802.3af/at/bt Compliant PoE

Provides Power Feeding up to 100 Watts

Power booster technologies for low voltage power inputs

Power Input & Connection
DC 9 to 55V redundant power, with one 4-pin removal

terminal block
19020000000165
4-pin Removal Terminal Block
for Power Inputs &
2-pin Removal Terminal Block
for Relay Fault Alarm
DIP Switch
4-pin Terminal Block Grounding Screw
Operating Temperature
Extended operating temperature model: -40°C to 75°C

Case/Installation
IP30 protection

DIN-Rail and Wall mount design

LED Indicators
LED Color Description
Green On Power input 1 or 2 is active
Power Red On Power input 1 or 2 is inactive, trigger relay
- Off Power input 1 and 2 is inactive
The PoE output port is supplying power to the
Amber On
powered-device over 2 pairs
The PoE output port is supplying power to the
Green On
powered-device over 4 pairs
The PoE output port is supplying power to the
powered-device over 2 pairs after the Dual PD
Amber Flashing Check event happens.
PoE
(Only occurs when Dual PD Check function is
disabled)
The PoE output port once supplied power to the
Green Flashing powered-device over 2 pairs and now recovers to
supply power over 4 pairs.
No powered-device attached or power supplying
Actual Consumption ≦30W
- Off
fails
31W≦ Actual Consumption ≦60W
- Off
61W≦ Actual Consumption ≦90W
Blue On
91W≦ Actual Consumption ≦100W
Red On
P/L
Red Flashing (Only occurs when PoE enhanced mode is
enabled)
DIP-Switch Setting
There are 2-set DIP-switch in front panel, that can be used for
setting the PoE Mode and Dual PD Check functions.
DIP-Switch ON
1 Enhanced PoE Mode
2 Dual PD Check Enabled Dual PD Check Disabled
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDI-X)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or
1000Base-T device connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
10Base-T,
Pins T568A Color T568B Color
100Base-TX
Pin 1 white/green stripe white/orange stripe Rx+
Pin 2 green solid orange solid Rx-
Pin 3 white/orange stripe white/green stripe Tx+
Pin 4 blue solid blue solid unused
Pin 5 white/blue stripe white/blue stripe unused
Pin 6 orange solid green solid Tx-
Pin 7 white/brown stripe white/brown stripe unused
Pin 8 brown solid brown solid unused
OFF (Default)
Standard PoE Mode
1000
Base-T(X)
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-