Related Manuals for ANTAIRA INJ-C200G-PASS-T
Summary of Contents for ANTAIRA INJ-C200G-PASS-T
- Page 1 INJ-C200G-PASS-T Industrial Gigabit Passive PoE Injector; EOT: -40°C ~ 75°C Hardware Manual Version 1.0 (December 2023)
- Page 2 Antaira Technologies, LLC may make improvements and/or changes to the product and/or specifications of the product described in this manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or typographical errors found in this guide. Changes are periodically made to the information contained herein and will be incorporated into later versions of the manual.
- Page 3 Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is ●...
- Page 4 Industrial Grade Passive PoE Injector Hardware Manual Version 1.0 (December 2023) The manual supports the following models: INJ-C200G-PASS-T ● This document is the current official release hardware manual. Please check our website (www.antaira.com) for any updated manual or contact us by e-mail (support@antaira.com).
-
Page 5: Table Of Contents
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 Table of Contents 1 Overview 1.1 Product Hardware Features 1.2 Package Contents 1.3 Safety Precaution 2 Hardware Description 2.1 Physical Dimensions 2.2 Front View Panel 2.3 Top View Panel 2.4 LED Indicators... -
Page 6: Overview
90 Watts of power to tail end devices. Each port supports 10/100/1000Tx with one port supporting PoE. The INJ-C200G-PASS-T is IP30 rated, DIN-rail and wall-mountable, and supports an extended operating temperature range of -40°C to 75°C, making it ideal for outdoor or harsh industrial applications. -
Page 7: Safety Precaution
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 1.3 Safety Precaution Attention: If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input. The industrial PoE injector’s hardware specs, ports, cabling information, and wiring installation will be described within this hardware manual. -
Page 8: Hardware Description
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 2 Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of this product series: (W x D x H) is 26mm x 75mm x 95mm... -
Page 9: Front View Panel
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 2.2 Front View Panel Figure 2.2, below, shows the front panel of the product series: Figure 2.2 - Front View Panel WARNING! Airflow around the switch must be unrestricted. To prevent the switch from overheating, there must be the following minimum clearances: ●... -
Page 10: Top View Panel
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 2.3 Top View Panel Figure 2.3, below, shows the top panel of the product series: Figure 2.3 - Top View Panel 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial PoE injector that display the power status and network status. -
Page 11: Cabling
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 ● RJ45 Pin Assignments Crossover Cable Straight Through Cable Pin Number / Signal Pin Number / Signal Pin Number / Signal Pin Number / Signal 1 / RX+... -
Page 12: Wiring The Power Inputs
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 2.7 Wiring the Power Inputs Caution: Please follow the steps below when inserting the power wire. Attention: Veuillez suivre les étapes ci-dessous lors de l'insertion du câble d'alimentation. -
Page 13: Grounding Note
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 2.8 Grounding Note Grounding and wire routing help limit the effects of noise due to Electromagnetic Interference (EMI). Run the ground connection from the ground screw to the grounding surface before connecting devices. The grounding screw symbol is shown below in Figure 2.9. -
Page 14: Mounting Installation
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 3 Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial PoE injector from the factory. If the DIN-Rail is not on the industrial PoE injector, please see Figure 3.1 to learn how to install the DIN-Rail on the switch. -
Page 15: Wall Mounting
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 Figure 3.2 - Insert the Switch on the DIN-Rail Figure 3.3 - Stable the Switch on the DIN-Rail 3.2 Wall Mounting Follow the steps below to mount the industrial PoE injector using the wall mounting bracket as shown below in Figure 3.4. - Page 16 Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 Figure 3.4 - Remove DIN-Rail bracket from the Switch Below, in Figure 3.5 are the dimensions of the wall mounting bracket. Figure 3.5 - Wall Mounting Bracket Dimensions...
-
Page 17: Hardware Installation
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 4 Hardware Installation 4.1 Installation Steps This section will explain how to install the industrial PoE injector: Caution: This device is intended for indoor use. Attention: Cet appareil est destiné à une utilisation en intérieur. -
Page 18: Maintenance And Service
Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 7. When all connections are set, the installation is complete. 4.2 Maintenance and Service ● If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. - Page 19 Antaira Technologies - Industrial PoE Injector INJ-C200G-PASS-T - Hardware Manual - v1.0 ○ Please contact Antaira for technical support service if the problem still cannot be resolved. If the industrial switch LED indicators are normal and the connected cables are correct but the ●...
Need help?
Do you have a question about the INJ-C200G-PASS-T and is the answer not in the manual?
Questions and answers