Advertisement
Quick Links
Advertisement
Related Manuals for BenQ W5800
Summary of Contents for BenQ W5800
- Page 1 W5800 Projector RS232 Command Control Installation Guide...
- Page 2 Table of Contents Introduction ............................. 3 Wire arrangement ................................ 3 RS232 pin assignment ..............................3 Connections and communication settings ..................4 RS232 serial port with a straight cable ........................4 Settings .................................. 4 RS232 via LAN ................................6 Settings .................................. 6 RS232 via HDBaseT ..............................
- Page 3 Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.
- Page 4 Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a straight cable D-Sub port (male or female) on a projector D-Sub 9 pin D-Sub 9 pin PC or laptop (male) (female) D-Sub 9 pin...
- Page 5 Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected. Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check...
- Page 6 RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. Input 8000 in the TCP port # field.
- Page 7 Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check None Stop bit 1 bit Flow control None...
- Page 8 Command table • Available features differ by projector specification, input sources, settings, etc.. • Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set. • Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. •...
- Page 9 Write Color + <CR>*color=+#<CR> Write Color - <CR>*color=-#<CR> Write Set Color value <CR>*color=value#<CR> Read Color value <CR>*color=?#<CR> Write Sharpness + <CR>*sharp=+#<CR> Write Sharpness - <CR>*sharp=-#<CR> Write Set Sharpness value <CR>*sharp=value#<CR> Read Sharpness value <CR>*sharp=?#<CR> Write Flesh Tone + <CR>*fleshtone=+#<CR> Write Flesh Tone - <CR>*fleshtone=-#<CR>...
- Page 10 Write Menu Position - Top-Left <CR>*menuposition=tl#<CR> Write Menu Position - Top-Right <CR>*menuposition=tr#<CR> Write Menu Position - Bottom-Right <CR>*menuposition=br#<CR> Write Menu Position - Bottom-Left <CR>*menuposition=bl#<CR> Read Menu Position Status <CR>*menuposition=?#<CR> Write Direct Power On-on <CR>*directpower=on#<CR> Write Direct Power On-off <CR>*directpower=off#<CR> Read Direct Power On-Status <CR>*directpower=?#<CR>...
- Page 11 Write Down <CR>*down#<CR> Write Right <CR>*right#<CR> Write Left <CR>*left#<CR> Write Enter <CR>*enter#<CR> Write Back <CR>*back#<CR> Write Source Menu On <CR>*sourmenu=on#<CR> Write Source Menu Off <CR>*sourmenu=off#<CR> Read Source Menu Status <CR>*sourmenu=?#<CR> Write 3D Sync Off <CR>*3d=off#<CR> Write 3D Sync On <CR>*3d=on#<CR> Write 3D Auto <CR>*3d=auto#<CR>...
- Page 12 BenQ.com © 2018 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.01-S...
Need help?
Do you have a question about the W5800 and is the answer not in the manual?
Questions and answers