Related Manuals for Sawo SAU-UI-S
Summary of Contents for Sawo SAU-UI-S
- Page 1 MANUAL ( SAU-UI-S ) Congratulations on your purchase of Saunova 2.0 Control Unit! Please read the manual carefully before using the control. Not for use in the USA, Canada and Mexico. ENGLISH...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. INTRODUCTION OF THE SAUNOVA 2.0 CONTROL 1. Introduction of the Saunova 2.0 Control ............3 1.1 Precautions ......................3 2. Operating Instructions ..................4 Congratulations on your purchase of Saunova 2.0 Control Unit! 2.1 Quick Start .......................4 2.2 Directions of Use .....................5 2.2.1 Heater on ....................5 Saunova 2.0 Control Unit is developed to enhance your sauna bathing with a variety of 2.2.2 Heater off ....................5... -
Page 3: Operating Instructions
Buttons and States (Illustration) 2.2 Directions of use For illustrative reference only. 2.2.1 Heater on Next, temperature, fan*, steamer* and Press the Power button to activate the session time (*not in all models) can be heater. The heater LED is illuminated changed if preferred. -
Page 4: Setting Mode
2.3.3 Cabin drying The state for “HOT” depends on the second 2.2.4 Setting Mode sensor, the bench sensor. If it is a temperature 10 minutes after the steamer session, the Press the Mode button to activate setting sensor only, and the bench temperature in heater will automatically dry the sauna room. -
Page 5: Assembly And Installation
3. ASSEMBLY AND INSTALLATION 3.2 Power Controller The heater is connected to the electrical network semi-stationarily with a H07RN-F The Power controller must not be located The Saunova Control Unit consists of the rubber cable or its equivalent. The use of inside the sauna room or in places Saunova Control Unit Interface, Saunova PVC-insulated cable as a connecting cable... -
Page 6: Technical Diagram
3.4 Technical Diagram Saunova 2.0 Fig. 5 Control Unit Main Switch RJ Data Cable For Heaters more than 9 kW Interface 1 1 0 1 CONTACTOR UNIT Heater >9 kW SESSION 1 2 3 SAU-UI-V2 CONTROL SAFETY SAFETY SWITCH Max. 9.0 kW SWITCH REM ON REM ON... -
Page 7: Sensors
3.5 Sensors 3.5.2 Sensor location with heaters mounted on mounted on the wall above the heater. Place the floor more than 200mm from the wall One or two sensors can be connected to the Top view Side view the sensor 150mm from the ceiling (Fig. 6 Power Controller. -
Page 8: Door Sensor/Switch (Optional)
3.7 Door Sensor/Switch 3.10 Installation for Separate User Interface (See IIlustration) open for more than 15minutes, an alarm and “oPEn” will be displayed to warn the user. The In other than household use, it is recommended 1. Mount the separate control panel in you preferred Connect the RJ cable provided from the heater will be switched off automatically. -
Page 9: Dip Switch
5. TROUBLESHOOTING 4. DIP SWITCH If an error occurs, the heater will be SESSION switched off. There will be a warning beep WARNING and the code for the error will be displayed Please note, only a qualified electrician or in the control panel. maintenance personnel is allowed to make the service operations and repairs! See more details on the table below. - Page 10 Other possible problems are: 4 LEDs in the power controller identifies errors. • The control unit is working fine, but • The steamer is on and “dry” is displayed, ERROR Description LED 1 LED 2 LED 3 LED 4 the heater does not turn on. Check the even though there is plenty of water Temperature sensor 1 is not connected.
-
Page 11: Subject To Change Without Notice
Bench Sensors 3kW) to maximum of Optional Bench Temperature Sensor Rated Voltage 3 Phases 400V 3N~ 18kW Bench Combined Temperature - Optional Frequency 50/60Hz Humidity Sensor Switching capacity per phase PX 4 Subject to change without notice. www.sawo.com | info@sawo.com...
Need help?
Do you have a question about the SAU-UI-S and is the answer not in the manual?
Questions and answers