Download Print this page

attica ATTFB01B102-BX Instruction Manual

21-23 ford bronco terra series rear bumper
Hide thumbs Also See for ATTFB01B102-BX:

Advertisement

Quick Links

Terra Series Rear Bumper
x 2
Before installation -
Read and understand all instructions,
warnings, cautions, and notes contained in this installation
instruction guide. Consult your vehicle owner's manual for proper
disconnection of electrical and li ting of vehicle if required for
installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing
this install please take this product to a trained professional.
A ter reading this guide please contact us with any questions or
concerns before installing product.
Customer Service: (626) 369-2121
ATTICA4X4 is not responsible for any bodily injury or harm to you or
your vehicle as a result of an improper install.
tech@attica4x4.com
21-23
Ford Bronco
ATTFB01B102-BX
Proper installation of this kit requires knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand
during the installation. Installation of this kit without proper
knowledge of the factory recommended procedures may a ect the
performance of these components and the safety of the vehicle.
Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all
installation hardware has been included. If parts are missing from kit, please be
prepared to provide the following information:
Name of purchase location
Bar Code on side of box
Date above Bar Code
Date insde box cover
(626) 369-2121

Advertisement

loading
Need help?

Need help?

Do you have a question about the ATTFB01B102-BX and is the answer not in the manual?

Questions and answers

Summary of Contents for attica ATTFB01B102-BX

  • Page 1 21-23 Ford Bronco Terra Series Rear Bumper ATTFB01B102-BX Before installation - Proper installation of this kit requires knowledge of the factory Read and understand all instructions, recommended procedures for removal and installation of original warnings, cautions, and notes contained in this installation equipment components.
  • Page 2: Tools Required

    tools required • 4mm hex tool • 10mm hex socket • 18mm hex socket hardw are kit b37 | bolt n09 | Hex Flange Nut b46 | hex head bolt W25 | spring Washer SPARE PARTS HARDWARE KIT Reinforcement plate W27 | Washer l bracket 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746...
  • Page 3 Begin by unpacking all items and inspecting them for damage or missing items. Any concerns, please contact the company you purchased the rear bumper from. A ter inspection, remove your factory rear bumper. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 4 Remove your backup parking sensor from your factory rear bumper and locate the mounting point on the Attica Terra Series Rear Bumper. Attach the backup parking sensor to the rear bumper using a B46 hex head bolt. Secure it in place with an N09 nut and a W25 washer, using a 4mm hex tool and a 10mm socket.
  • Page 5 The opposite end will then connect to your rear bumper lights. *The extra connecters are used for our Attica Terra Series Side Steps and Roof Rack lighting. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM...
  • Page 6 Next, position the L bracket on both sides of the rear bumper as shown below. A ter positioning the L bracket, align the rear bumper in place as shown above. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 7 Use a B37 bolt and a W27 washer. Thread it into the nut on the L bracket using an 18mm socket. Use the factory bolts and Attica reinforcement plate, tighten four bottom bolts using an 18mm socket. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM...
  • Page 8 The last step is to reconnect the parking sensor harness. Once finished, your Attica Terra Series Rear Bumper will be completely installed and ready to take to the outdoors! 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 9 if you have any questions, please email us at tech@attica4x4.com or call us at 626-369-2121 (626) 369-2121 tech@attica4x4.com...