Advertisement
IMPORTANT:
KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT
HARNESSED CAR SEAT
Instructions for Installation & Use
Series No. 8300/A/2013
Series No. 8300/B/2013
SICT - HEAD & TORSO SIDE
IMPACT CUSHION TECHNOLOGY
HARNESSED FOR LONGER
HASSLE FREE HARNESS
Instructions for Installation & Use
FORWARD
FACING
6 months to
8 years (approx)
1
Advertisement
Table of Contents
Related Manuals for Britax safe-n-sound 8300/A/2013
Summary of Contents for Britax safe-n-sound 8300/A/2013
- Page 1 HARNESSED CAR SEAT Instructions for Installation & Use Series No. 8300/A/2013 Series No. 8300/B/2013 FORWARD FACING 6 months to 8 years (approx) SICT - HEAD & TORSO SIDE IMPACT CUSHION TECHNOLOGY HARNESSED FOR LONGER HASSLE FREE HARNESS IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT Instructions for Installation &...
- Page 2 INSTALLATION QUICK SETUP INSTALLATION QUICK SETUP 25MM Remove Pull Slack PUSH Click Store Attach Pull Instructions for Installation & Use Instructions for Installation & Use...
- Page 3 INTRODUCTION INTRODUCTION Chỉ được sử dụng ở vị trí hướng mặt về phía trước cho em nào có vai ở trên vạch ghi độ cao của To be used only in a forward-facing position by a child whose shoulders are above the lower shoulder vai ở...
- Page 4 INTRODUCTION INTRODUCTION 肩膀超过靠下肩高标记的婴儿（大约6个月的宝宝）只采用前向式安装，直到儿童肩膀达 के व ल उस शिशु द् व ारा मात् र सामने की दिशा की स् थ िति मे ं प् र योग किया जाना चाहिए जिसके कन् ध े कन् ध े के निचले भाग से ऊपर आ गए 到靠上的肩高标记（大约8岁的儿童）。...
- Page 5 Carefully read all the instructions for installation in this book. If in doubt about the method of installation, consult Britax or agent or a child restraint fitter or, in New Zealand, to consult the agent for the vehicle. HOW TO INSTALL THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT UPPER ANCHORAGE POINT IN THE CAR.
- Page 6 IMPORTANT : • Fit the restraint firmly to the car seat. • Regularly check the restraint components, straps and other fitments for correct function and condition. Seek prompt repair. • Fit the harness firmly to the child. • IF AN AIRBAG IS FITTED IN THE SEATING POSITION WHERE THE CHILD RESTRAINT IS TO BE •...
-
Page 7: Special Features
SPECIAL FEATURES SPECIAL FEATURES 20 21 Harness Tongues Harness Buckle 13. Top Tether Storage Pocket (attached to cover) 14. Instruction Book Storage Pocket 15. Pocket (if fitted) 16. Path for the car's Lap-sash seatbelt or lap only seatbelt 17. Adjustable Recline Foot 18. -
Page 8: Shoulder Height Markers And A Growing Child
When the child’s shoulders reach to approximately 4 years of age. this upper marker, or the child no However, Britax recommends that you keep your longer fits in the child restraint, child in a rearward facing restraint for as long as... - Page 9 A lap seatbelt on the child's abdomen is dangerous; it may cause injury in a crash. Use a booster seat suitable for children up to 8-10 years of age and a Child Harness suitable for use with the booster seat. Britax Recommends: Safe-n-Sound Encore 10 Booster Seat Safe-n-Sound Protecta Plus Child Harness...
-
Page 10: How To Install
Slot Anchor plate Child legs If the car seatbelt does not remain firm in everyday use, then contact the retailer, or Britax Safe-n-Sound customer service for a gated 3-bar slide (order No. 0215). IMPORTANT : Ensure that the child restraint is not over reclined. The backrest should not be reclined more then 45°. - Page 11 We To lengthen the top tether strap, fully press adjuster button recommend the use of the Britax Safe-n-Sound™ Messy (A) while pulling top tether strap (B) to slacken as shown Mat or other protection under and behind the seat to keep left.
- Page 12 HOW TO INSTALL HOW TO INSTALL TO REMOVE RESTRAINT FROM VEHICLE G. Pull the top tether adjustment strap (C) to remove any slack Fully press adjuster button (A) but do not tighten. while pulling top tether strap (B) A. Disengage seatbelt tongue from buckle and remove from Fold up excess strap and use pocket to store excess strap to lengthen.
-
Page 13: How To Use
HOW TO USE HOW TO USE SHOULDER HARNESS FEATURES ADJUSTING EASY ADJUST™ HEADREST AND HARNESS STRAP HEIGHT Correct fitment of the harness is very important as it restrains the child in the restraint. The harness must fit firmly around A. You do not need to remove the restraint from the vehicle to the upper torso of the child and be positioned so as to leave adjust the harness or headrest positions. - Page 14 HOW TO USE HOW TO USE C. Release the AHR Easy Adjust Headrest B. Fit either harness tongue into the harness buckle followed Lift the lever Tongue Lever so that it locks into position. Ensure by the other tongue. A click is heard when the second at the top of that it has locked in position by gently tongue is fully engaged.
-
Page 15: Care And Maintenance
(gentle cycle), cold water only, rinse well and dry on a flat surface. Do not tumble dry, If the harness buckle cannot be returned to its original bleach or dry-clean. working condition then contact BRITAX Customer Service for assistance. Contact details on page 43. Instructions for Installation & Use... - Page 16 Lift elastic over headrest wings while peeling away headrest cover. Pull to unclip press stud VERY IMPORTANT : Only replace the cover with BRITAX Safe-n-Sound supplied replacement cover with identical shoulder height markers or a replacement cover meeting AS/NZS 8005.
- Page 17 CARE & MAINTENANCE CARE & MAINTENANCE TO REPLACE COVER: E. Unhook the elastic loops at the bottom of the restraint Attach the elastic loops at the Unhook the elastic loops at the located under the front of the restraint, and at the back of the back of the restraint back of the restraint A.
-
Page 18: Accessories & Features
If an aftermarket accessory is headrest wings. used that is not recommended by Britax Safe-n-Sound then ensure that the accessory is for this restraint and compliant with AS/NZS 8005 and stated as suitable for use with this child restraint. - Page 19 ACCESSORIES & FEATURES ACCESSORIES & FEATURES MESSY MAT™ SEAT PROTECTOR EZ BUCKLE SYSTEM (WHERE FITTED) Long Messy Mat™ INSTRUCTIONS (IF SUPPLIED) EZ Buckle system retains the harness buckle in a forward position and prevents the child from sitting on the buckle when Ribs Place ribbed or pocket end of the Messy Mat seat protector on boarding.
-
Page 20: Installation Of Car's Upper Anchorage Point
Some vehicles may have an anchor fitting fitted by the vehicle manufacturer. If Length 300mm (Use Britax Safe-n-Sound part 0035). anchorage points cannot be found refer to car manufacturer or local child restraint fitting station or traffic Length 600mm (Use Britax Safe-n-Sound part 0036). - Page 21 CAR INSTALLATION ACCESSORIES for vehicle inspection to find the best, correct position for structure (From retailers of Britax Safe-n-Sound products) the placement of the upper anchorage point, and for the Reinforcing correct attachment bolt length and use of spacers. In New EXTRA ANCHOR KITS: Available for using the restraint in additional cars.
-
Page 22: In Case Of Crash
To assist you in making an accident insurance claim cut the following statement and The Britax Safe-n-Sound Crash Exchange Program is a voluntary program designed to ensure that our include it with your claim. children are safe and that any seat that may have experienced a severe crash is taken out of the market. - Page 23 The BRITAX Safe-n-Sound trademark is the property of Britax Childcare Holdings Ltd, UK. We reserve the right to alter this product without notice. © 1995-2016 Britax Childcare Pty. Ltd. This product is covered by Australian and overseas patent applications. Part No.2202608A...
Need help?
Do you have a question about the safe-n-sound 8300/A/2013 and is the answer not in the manual?
Questions and answers