Password Security - HP SignagePlayer mp8000r Illustrated Parts And Service Map

Password Security

Establishing a Setup or Power-On password:
1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down >Restart.
2. As soon as the computer is turned on, press F10 when the monitor light turns green to enter
Computer Setup. Press Enter to bypass the title screen, if necessary. If you do not press F10
when prompted, a restart will be necessary.
3. To establish a Setup password, select Security > Setup Password and follow the instructions
on the screen.
- or -
To establish a Power-On password, select Security > Power-On Password and follow the
instructions on the screen
4. Before exiting, click File > Save Changes and Exit.
Changing a Setup or Power-On password:
1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart.
To change the Setup password, go to step 2.
To change the Power-on password, go to step 3.
2. To change the Setup password, as soon as the computer is turned on, press F10 when the
monitor light turns green to enter Computer Setup. Press Enter to bypass the title screen, if
necessary.
3. When the key icon appears, type your current password, a slash (/) or alternate delimiter
character, your new password, another slash (/) or alternate delimiter character, and your new
password again as shown:
current password/new password/new password.
NOTE: Type the new password carefully since the characters do not appear on the screen.
4. Press Enter.
The new password will take effect the next time the computer is restarted.
Deleting a Power-On or Setup password
1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart.
To delete the Setup password, go to step 2.
To delete the Power-On password, go to step 3.
2. To change the Setup password, as soon as the computer is turned on, press F10 when the
monitor light turns green to enter Computer Setup. Press Enter to bypass the title screen, if
necessary.
3. When the key icon appears, type your current password followed by a slash (/) or alternate
delimiter character as shown. Example: currentpassword/
4. Press Enter.
Clearing CMOS
1. Turn off the computer and any external devices, and disconnect the power cord from the
power outlet.
2. Remove the chassis access panel.
3. On the system board, press and hold the CMOS button for 5 seconds.
4. Replace the chassis access panel and reconnect the power cord.
5. Turn on the computer and allow it to start.
mp8000r, SFF Chassis
Diagnostic LEDs
LED Color LED Activity
Power Red 2 blinks, 1 blink every second
followed by a 2 second pause
Power Red 3 blinks, 1 blink every second
followed by a 2 second pause
Power Red 4 blinks, 1 blink every second
followed by a 2 second pause
Power Red 5 blinks, 1 blink every second
followed by a 2 second pause
Power Red 6 blinks, 1 blink every second
followed by a 2 second pause
Power Red 7 blinks, 1 blink every second
followed by a 2 second pause
Power Red 8 blinks, 1 blink every second
followed by a 2 second pause
Power Red 9 blinks, 1 blink every second
followed by a 2 second pause
Power Red 10 blinks, 1 blink every second
followed by a 2 second pause
none none System does not power on and
LEDs are not flashing
Common POST Error Messages
Screen Message
101-Option ROM Error
103-System Board
Failure
164-Memory Size Error
and
201-Memory Error
214-DIMM Configura-
tion Warning
301-, 304-Keyboard error
501-Display Adapter
Failure
1720-SMART Hard Drive
Detects Imminent Failure
1796-SATA Cabling Error One or more SATA devices
1801-Microcode Patch
Error
643118-001
State/Message
CPU thermal shutdown
Processor not installed
Power failure (power supply overload)
Pre-video memory error
Pre-video graphics error
System board failure (ROM
Invalid ROM based on Checksum
System powers on but is unable to boot
Bad option card
System unable to power on
Probable Cause Recommended Action
1. System ROM checksum 1. Verify ROM, reflash if required
error.
2. Remove suspected card, reboot
2. Expansion board option
3. Clear CMOS memory, reboot
ROM checksum
4. Replace system board
DMA, timers 1. Clear CMOS memory.
2. Remove expansion boards.
3. Replace system board.
Incorrect memory configu- 1. Run Setup (F10).
ration
2. Check DIMMs for proper
seating, type, and HP
compatibility.
3. Remove DIMMs singularly and
reboot to isolate faulty DIMM.
4. Replace system board.
Populated DIMM configura- Rearrange the DIMMs so that
tion is not optimized each channel has the same amount
of memory.
Keyboard failure. Check keyboard connection or
keys. Check connector for bent of
missing pins. Replace keyboard. If
304, possible system board prob-
lem.
Graphics display controller. 1. Reseat graphics card.
2. Clear CMOS.
3. Check monitor connection.
4. Replace graphics card.
Hard drive is about to fail. 1. Determine if hard drive is
giving correct error message.
Enter Computer Setup and run
the Drive Protection System
test under Storage > DPS Self-
test.
2. Apply hard drive firmware
patch if applicable.
3. Back up contents and replace
hard drive.
Ensure SATA connectors are used
are improperly attached. For in ascending order. For one
optimal performance, the device, use SATA 0. For two
SATA 0 and SATA 1 con- devices, use SATA 0 and SATA 1.
nectors must be used before For three devices, use SATA 0,
SATA 2 and SATA 3. SATA1, and SATA 2.
Processor not supported by 1. Upgrade BIOS to proper
ROM BIOS.
version.
2. Change the processor.
page 4