1. Manuals
  2. Brands
  3. Zenith Manuals
  4. TV Receiver
  5. HCS5650
  6. Installation and operating manual

Zenith HCS5650 Installation And Operating Manual

Hd integrator box system
Hide thumbs Also See for HCS5650:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operating Guide | Warranty
Model Number | HCS5650 | HD Integrator Box System
© Copyright 2008, LG Electronics U.S.A., Inc.
t a b l e o f c o n t e n t s
installer quick setup guide
Zenith and the lightning Z logo are registered
trademarks of Zenith Electronics Corporation
5
page
75
page

Advertisement

Table of Contents
loading

Related Manuals for Zenith HCS5650

Summary of Contents for Zenith HCS5650

  • Page 1 Installation and Operating Guide | Warranty Model Number | HCS5650 | HD Integrator Box System t a b l e o f c o n t e n t s page installer quick setup guide page Zenith and the lightning Z logo are registered trademarks of Zenith Electronics Corporation ©...

  • Page 2: Safety Warnings

    CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 2000 Millbrook Drive, Lincolnshire, IL 60069.
  • Page 3 Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. COMPLIANCE: The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc., 2000 Millbrook Drive Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000...

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.

  • Page 5: Table Of Contents

    To perform a normal installation set up, you need an installer's remote and the LT2002 Quickset II Clone Programmer – both are shown and described in later sections. See your Zenith/LG dealer if you wish to purchase the Installer remote and LT2002.

  • Page 6: Setup Checklist

    TV? Y: Install VESA Prior to Operation *Note: Bracket on TV following the instructions After installing a PPV card in the HCS5650 The HD Integrator Box System must be be sure to disconnect the AC power cord for supplied with the bracket.

  • Page 7: Installation/Connections Overview

    STATUS LED The STATUS LED flashes while the program is running. RESET Press RESET to start the program that re-initializes the HCS5650. UPDATE Press UPDATE to allow software to be updated. To start the download program, press and release the RESET button while holding down the UPDATE button.

  • Page 8: Ventilation

    Ventilation The HCS5650 Integrator Box as well as LCD monitors(M3701C-BH and M4201C-BH) generate heat during operation and need to be provided with adequate ventilation to assure continued reliable operation. See recommendations below. Ventilation Clearance Proper clearance for air to flow around the HCS5650 Integrator Box must be provided.

  • Page 9: Installation Overview

    Monitor/Integrator Box Wall Mounting System The LCD monitor and Integrator Box can be mounted to a wall using an optional Monitor/Integrator Box wall mounting system. For further information on the mounting system, see your LG dealer. P A G E 9...

  • Page 10: Aux Controller: Connection And Placement

    AUX Controller: Connection and Placement Connect the AUX Controller to allow the Integrator Box to operate your AUX device. Connect the AUX Controller to the AUX CONTROL cord on the TV/STB. Place the AUX Controller under and in front of the AUX device. The AUX Controller must extend just out in front of the infrared sensor on the AUX device.

  • Page 11: Antenna

    Antenna Hookup Connect an off-air antenna to the HD Integrator Box System. Locate the Antenna/Cable jack on the back of the HD Integrator Box System. PILLOW AC OUT AC IN AUDIO IN AUDIO OUT RS-232C REMOTE PILLOW JACK IN DIGITAL DIGITAL AUDIO DISPLAY DIGITAL...

  • Page 12: Cable Service

    Cable Service Hookup Connect cable service to the HD Integrator Box System. AC OUT AC IN AUDIO IN AUDIO OUT RS-232C REMOTE INTERFACE DIGITAL DIGITAL AUDIO DISPLAY DIGITAL MAX 8A 960W AC 120V~ 60Hz CONTROL VIDEO OUT OUT (OPTICAL) CONTROL VIDEO IN Locate the Antenna/Cable jack on the back of the TV/STB.

  • Page 13: Rs-232C Control Connections

    RS-232C Control Connections Connect the Display Control (RS-232C) port from the TV/STB to the display panel to control TV functions with RS-232C commands PILLOW AC OUT 8A AC IN 120V~ 60Hz AUDIO IN AUDIO OUT SERVICE REMOTE PILLOW JACK IN DIGITAL DIGITAL AUDIO DISPLAY...

  • Page 14: Viewing Equipment Setup

    LCD Display Panel Setup for use with the TV/STB Commercial Interface Control Box. Connect RS-232C cable. (See previous page.) Connect IR Receiver cable to Remote In HCS5650 PTC INSTALLER MENU port. INSTALLER SEQ Connect the Cable Out jack to the display panel, typically the Antenna (In) jack.

  • Page 15: Computer Pc Hookup (Dvi)

    Computer PC Hookup (DVI) PILLOW AC OUT 8A AC IN 120V~ 60Hz AUDIO IN AUDIO OUT SERVICE REMOTE PILLOW JACK IN DIGITAL DIGITAL AUDIO DISPLAY DIGITAL (12V DC 40mA) CONTROL VIDEO OUT OUT (OPTICAL) CONTROL VIDEO IN Locate the computer DVI out port on the computer.

  • Page 16: Audio Connection - Digital Audio Optical Connections

    Audio Connection – Digital Audio Optical Connections PILLOW AC OUT 8A AC IN 120V~ 60Hz AUDIO IN AUDIO OUT SERVICE REMOTE PILLOW JACK IN DIGITAL DIGITAL AUDIO DISPLAY DIGITAL (12V DC 40mA) CONTROL VIDEO OUT OUT (OPTICAL) CONTROL VIDEO IN Connections Panel From Digital Audio Optical Out...

  • Page 17: On-Screen Menus Overview

    On-Screen Menus Overview Descriptions of the menus and on-screen displays. Menu Name Page Description ON-SCREEN MENUS CHANNEL MENU Adjusts the basic operational features of the TV. Auto Program Automatically finds and stores active channels to scroll through using Channel Up/Down. Channel List Manually picks and chooses which active channels will appear when using Channel Up/Down.

  • Page 18: Pillow Speaker Setup

    Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a LG patented technology and is being implemented by certain brands of “smart” pillow speakers, such as Curbell’s “GEN-II” models.

  • Page 19: Other Menus And On-Screen Displays

    Other Menus & On-Screen Displays Use the remote keys indicated below to access these menus and displays. In this manual, the OSD (On Screen Displays shown) may be different than those on the actual TV. The following are generic examples to familiarize you with the TVs options. TIMER English Volume Display...

  • Page 20: User Remote Control Key Functions

    User Remote Control Key Functions A list of the keys and their functions on the optional user remote control, not supplied with the HD Integrator Box System. MUTE Turns sound Off and On, while the picture remains. POWER BANK Turns TV On or Off. Press and repeat to select a Channel Memory Bank - - 1, 2, 3, or 4 (Standby).

  • Page 21: Installer Remote Control Key Functions

    Installer Remote Control Key Functions A brief list of the keys on the optional installer’s remote and what they do. MUTE Turns sound Off and On, while the picture remains. POWER Turns TV On or Off. BANK Press and repeat to select a Channel GUIDE Memory Bank - - 1, 2, 3, or 4 (Standby).

  • Page 22: Auto Program (Do A Channel Search)

    Auto Program (Channel Search) Use Auto Program to automatically find and store all of the channels available in the selected Tuning Band. *Notes: Tuning Band must be set before doing the channel search. See Installer menu item 003 Band/AFC. Default setting is 1, for CATV. When Auto Program is run, any assigned channel labels are automatically cleared.

  • Page 23: Channel List

    Channel List After the channel search, remove unwanted channels. Press the MENU button and then use the ADJ button Antenna to highlight the Channel menu and press the OK (Enter) Auto Program button. Channel Label Channel List Use the ADJ button to highlight Channel List and Fine Tune Auto...

  • Page 24: Channel Labels Setup

    Channel Control (Continued) Channel Labels Setup - Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the Channel Labels option highlighted, use the ADJ D E F G buttons to scroll through the available channel labels, such as, A&E, AMC, ESPN, HBO, etc.

  • Page 25: Unstable Screen

    Channel Control Unstable Screen - If a dashed line or no color appears, the screen is unstable, therefore try channel adjustments. Antenna Auto Program (This is only available for analog broadcasting.) Channel Label Channel List Press the MENU button and then use the ADJ button Fine Tune Auto...

  • Page 26: Clock Setup

    Clock Setup (Continued) Manual Time Settings - Use the ADJ D E F G buttons to set the year, month, day, hours and minutes. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter)
  • Page 27 Clock Setup (Continued) Automatic Time Settings - If you select auto time setting, time will be set from the digital broadcast information. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter)
  • Page 28 Clock Setup (Continued) Daylight Saving - Installer can select to use Daylight Savings to adjust the clock time. This is operated from the Automatic Time Settings. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter)
  • Page 29 Clock Setup (Continued) TV Activation Time Settings - You can set a time for the TV to automatically turn-on. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.

  • Page 30: Clock Setup

    Clock Setup Auto Off - If there is no signal on the TV for 15 minutes or more, or if no button is pressed for more than 3 hours, this function turns off the TV Time automatically. V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button...
  • Page 31 V-Chip (Continued) Entering a PIN (Password) - This option sets up or changes the password for blocking program ratings. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.
  • Page 32 V-Chip (Continued) Set Block Hour. - This option sets up hour that you wish to block. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.
  • Page 33 V-Chip (Continued) TVPG Ratings - You can block programs based on the TV program rating. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.
  • Page 34 V-Chip (Continued) MPAA Ratings - Restricting movies by their rating. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.
  • Page 35 V-Chip (Continued) Canadian English Ratings Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button. 11:20 PM Sep.11, 2006 Move Select Menu...
  • Page 36 V-Chip (Continued) Canadian French Ratings Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button. 11:20 PM Sep.11, 2006 Move Select Menu...

  • Page 37: V-Chip

    V-Chip Your TV’s OSD (On Screen Display) may differ slightly from what is shown in this manual. Downloadable Rating Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.

  • Page 38: Caption Menu

    Caption Menu (Continued) Turn Captions On/Off *Note: Pressing CC on the remote to select a captions option will also turn closed captions on. On/Off Analog Mode Digital Mode Digital Font Option Press the MENU button and then use the ADJ button to highlight the Caption menu and press the OK (Enter) button.

  • Page 39: Caption Menu

    Caption Menu Digital Captions Mode - Digital Captions only appear on digital channels, tune in a digital channel that is actually broadcasting digital captions. On/Off *Note: Pressing CC on the remote selects a captions option. Analog Mode Digital Mode Service1 Digital Font Option Press the MENU button and then use the ADJ button...
  • Page 40 Sound Menu (Continued) Digital Audio Output Settings - Set the digital audio output as Dolby Digital or PCM. Digital Output Auto Volume Multi-Track English Press the MENU button and then use the ADJ button to highlight the Sound menu and press the OK (Enter) button.
  • Page 41 Sound Menu (Continued) Automatic Volume Control Settings - Have the TV automatically maintain the same sound level between different channels. Digital Output Auto Volume Multi-Track English Press the MENU button and then use the ADJ button to highlight the Sound menu and press the OK (Enter) button.

  • Page 42: Sound Menu

    Sound Menu Digital Audio Settings - You can set digital audio language. (This is only available for digital broadcasting.) Digital Output Auto Volume Multi-Track English Press the MENU button and then use the ADJ button to highlight the Sound menu and press the OK (Enter) button.

  • Page 43: Language Control

    Language Control Menu Language - The menus can be shown on the screen inter selected language. First select your language. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.

  • Page 44: Set Id

    Set ID Set ID - Use this function to specify a set ID number. Time V-Chip Menu Language English Menu Transparency Semi Opaque Press the MENU button and then use the ADJ button Set ID to highlight the Setup menu and press the OK (Enter) button.
  • Page 45 Picture Menu (Continued) Picture - Preset - Set the picture mode to the program content, e.g. Dynamic or Mild etc. (This is only available for analog broadcasting.) Mode Standard Color Temperature Normal Screen Format 16:9 Noise Reduction Off Press the MENU button and then use the ADJ button Film Mode to highlight the Picture menu and press the OK (Enter)
  • Page 46 Picture Menu (Continued) Manual Picture Adjustment To make custom picture settings, set the Mode to Manual on the menu. Use the Manual settings for the best presentation of movies. Mode Standard Color Temperature Normal The patient will then be able to view movies with more realism. Screen Format 16:9 Noise Reduction Off Press the MENU button and then use the ADJ...

  • Page 47: Picture Menu

    Picture Menu Noise Reduction - The user can watch movies with a more realistic picture on analog channels. Mode Standard Color Temperature Normal Screen Format 16:9 Noise Reduction Off Press the MENU button and then use the ADJ button Film Mode to highlight the Picture menu and press the OK (Enter) button.
  • Page 48 Channel Banks Setup For Hospital Applications Channel Banks Overview Purpose of Channel Banks: Allows the institution administrator to control access to CHANNEL PREVIEW - BANK 1 patient in-room TV programming. For Banks 1, 2 and 3, the institution can create programming levels.
  • Page 49 Installer Remote Control Key Functions for Channel Banks Menu CHANNEL PREVIEW - BANK 1 Shows selected Channel Bank. Shows selected Channel or Aux source. CH 011-001 NORMAL-ADDED Shows channel status in selected bank. In Channel Banks menu, use the Left/Right arrows to select: Normal-Added Channel will appear in channel scan.

  • Page 50: Managing The Channel Banks

    Managing The Channel Banks The TV has four channel banks, where the administrator or installer can store groups of TV channels. PLANNING THE CHANNEL BANKS ADDING / DELETING CHANNELS A previously prepared programming chart is helpful. Generally, TV channels are grouped into “program packages” 1.
  • Page 51 Managing The Channel Banks Examples of typical channel banks chars filled in Figure 1. Typical channel banks after running Auto Program Purpose Channel Number 9 10 11 12 13 14 16 17 19 20 A = Active - - Channel was found during AUTO PROGRAM Figure 2.
  • Page 52 Managing The Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) Purpose Channel Number 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Purpose Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50...

  • Page 53: Commercial Mode Setup

    Commercial Mode Setup Following is the Commercial Mode Operation Setup. Operating Installer Menu To set up the controls for the TV you will need to know how to enter the HCS5650XX PTC INSTALLER MENU TV/STB Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV/STB Installer menu and how to make and save changes in the menu.

  • Page 54: Commercial Mode Setup

    Commercial Mode Setup This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed instructions at each step; how to access and use the Installer menu etc. *Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program (Channel search) is disabled if there is an Aux input active.

  • Page 55: Cloning Connections/Learning Setup

    Cloning Connections/Learning Setup Connections for the LT2002 Clone Programmer to Learn the TV/STB Master TV Setup. THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK= XX:XX TV CLOCK= XX:XX -PRESS ANY KEY TO CONTINUE.

  • Page 56: Clone Programmer Learning Setup

    POWER, OR ENTER Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability. After the time is copied to the Clone programmer, the current time can then be transferred to another TV.

  • Page 57: Cloning Connections/Teaching Setup

    Cloning Connections / Teaching Setup Teaching the Master Setup to Another TV/STB Connections for the LT2002 to Teach another TV/STB the Master Setup THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK= XX:XX TV CLOCK=...
  • Page 58 Installer Menu (Continued) Use the Installer’s Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote HCS5650XX PTC INSTALLER MENU control.
  • Page 59 Installer Menu (Continued) Installer Menu Items 031 through 117 Menu Item Function Value Range Default Value Brief Description of Function and Comments POLL RATE 20 ~ 169 Selects poll rate for M.P.I. TIMING PULSE 186 ~ 227 Sets baud rate for M.P.I. CAMPORT EN 0 / 1 Set to 1 to enable Video 2 input.
  • Page 60 Installer Menu (Continued) Detailed Descriptions of Installer Menu Items Generally, this feature is used in connection with START CHANNEL (Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV/STB will remain 000 - INSTALLER SEQUENCE locked on Channel 3.
  • Page 61 Pay-Per-View provider. Sets baud rate. Step size of 4.3 020 - FEATURE LEVEL Default set to ZEN 1 for LG IR remote control opera-tion. Set O, P LBL for LG Private Label IR remote con-trol 034 - CAMPORT EN. (Camera Port Enable) operation.
  • Page 62 Installer Menu (Continued) (Continued from previous page) 036 - FRONT Y/C EN. (HDMI 2 Enable) 075 - REVERT CH (Revert to Start Channel) Set to 1 to enable display panel HDMI 2 input. If set to 1 and loss of M.P.I. communication occurs, TV automatically Set to 0 to disable display panel HDMI 2 input.

  • Page 63: Installer Menu

    Installer Menu (Continued from previous page) 087 - REAR RGB EN. (Rear RGB1 Enable) 105 - VID OUT FORMAT Controls access to rear RGB1 input on display panel. 0=1080i 1=720p 2=480p Set to 1 to enable RGB1 input for DTV. Set to 2 for PC. Set to 0 to disable RGB1 input.

  • Page 64: Reference

    Reference: TV Features / Menus that can be Cloned Clonable Menu Features Channel Picture Sound Setup Caption Auto Program (Active Mode Mode Time On/Off channels found with Contrast Treble Clock Analog Mode the channel search) Brightness Bass Auto Off Digital Mode Channel Labels Color Balance...
  • Page 65 Reference: Procedures for adding Channel Label Icons/Custom Channel Labels (2-5-4 + MENU Mode) Adding Channel Icons and Labels in the 2-5-4 + Menu Mode Editing/Adding Channel ICONs and/or Labels Editing and adding the labels can only be done if there are If there is no pre-assigned ICON, you can make a channel label of up channels entered into the TV/STB’s channel map either by to 7 characters to help in identifying the channel or network.
  • Page 66 Reference: Detailed Information For Making A Master TV IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how to adding channel icons or channel labels are not correctly added, then enter the TV/STB Installer menu and make changes to the cloned TV/STB will all have problems.
  • Page 67 Reference: Software Version Check Procedure to Check Software Version The software version of the TV/STB may be checked by accessing the INSTALLER MENU. To do this, press the MENU button at least 10 times until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "OK (Enter/Select)".

  • Page 68: Tv/Stb Aux Input Configuration

    TV/STB Aux Input Configuration TV/STB Aux Input Configuration ENABLE MPI DATA MPI DATA DATA STATUS DATA DIRECT ACCESS STATUS TV/STB STATUS TYPE TYPE 0xD2 STATUS Tuning Installer Menu 0x41 SOURCES CURRENT AV TYPE 0X0D SOURCE ENABLED (R/W) SOURCE (R) ASSIGNMENT SOURCE OLD_OCV OLD_OCV...

  • Page 69: Monitor Requirments/Rs-232 Troubleshooting

    TV/STB RS-232 Monitor Requirements / RS-232 Troubleshooting RS-232 Communication Requirments RS-232 Pin Configuration Wiring Diagram of the TV/STB Display Control Connector Type of Connector; D-Sub 9-Pin Female Pin Name No Connection TXD (Transmit data) RXD (Receive data) No Connection No Connection No Connection No Connection No Connection...

  • Page 70: Rs-232C Control

    RS-232C Control Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. Connecting the cable Connect the RS-232C cable as shown in the picture. - The RS-232C protocol is used for communication between the PC and product.
  • Page 71 RS-232C Control 1. Key(Command : m c) To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code : Refer to page A18. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] Code(Hexa) Function Note Channel Up Button Channel Down Button VOL(+) R/C Button VOL(-)

  • Page 72: Troubleshooting

    -Check that “+” and “-” match in battery compartment. • Too much light in room. -Dim room light. • Wrong Installer remote control. -Requires compatible Installer remote, contact your LG dealer. • Incorrect Bed 1-2 setting. -Set correct Bed 1-2 setting. Picture Reception Normal picture, poor •...
  • Page 73 Reference: Cloning Procedure Troubleshooting Warning: Do not use LT2002 while a LodgeNet PPV card is installed in TV or clone programmer will be damaged. Note The LT2002 programmer is designed to be used with TVs con- Reset Clone After Static Shock taining the 221-01006 and later processors.
  • Page 74 Troubleshooting Flow Chart P A G E 7 4...

  • Page 75: Installer Quick Setup Guide

    Installer Quick Setup Guide See the installation and setup guide of the particular TV for more information. *Note: After installing a Pay-Per-View card, be sure to remove and reconnect the TV/STB AC power cord. Connections Panel PILLOW AC OUT 8A AC IN 120V~ 60Hz AUDIO IN AUDIO OUT...

  • Page 76: Glossary Of Terms

    Glossary of Terms A list of definitions for some of the words found in this guide 75 OHM RF CABLE DIGITAL TELEVISION OUTPUT The wire that comes from an off-air antenna or High-resolution, cinema-quality television Refers to the output jack that sends a signal cable service provider.
  • Page 77 Memo P A G E 7 7...
  • Page 78 Memo P A G E 7 8...
  • Page 79 Memo P A G E 7 9...

  • Page 80: Warranty

    HD Commercial Interface STB Welcome to the LG family! We believe that you will be pleased with your HD Commercial Interface STB. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A.

Table of Contents