Download  Print this page

Pioneer MVH-P7300 Installation Manual

Rds media center receiver.
Hide thumbs
   

Advertisement

RDS MEDIA CENTER RECEIVER
AUTORADIO MULTIMEDIA RDS
RECEPTOR Y CENTRO DE COMUNICACIONES RDS
MVH-P8300BT
MVH-P7300
Installation Manual
Manuel d'installation
Manual de instalación
  Printed in Thailand 
  Imprimé en Thaïlande
YRD5343-A/N
<
> UC
<KKMZX> <10K00000>
Connecting the unit
English
WARNING
WARNING
• To avoid the risk of accident and the potential
• Use speakers over 50 W (output value) and
violation of applicable laws, no viewing of front
between 4 W to 8 W (impedance value). Do not use
seat video should ever occur while the vehicle is
1 W to 3 W speakers for this unit.
being driven.
• The black cable is ground. When installing this
• In some countries or states the viewing of images
unit or power amp (sold separately), make sure
on a display inside a vehicle even by persons
to connect the ground wire first. Ensure that
other than the driver may be illegal. Where such
the ground wire is properly connected to metal
regulations apply, they must be obeyed.
parts of the car's body. The ground wire of the
power amp and the one of this unit or any other
device must be connected to the car separately
with different screws. If the screw for the ground
CAUTION
wire loosens or falls out, it could result in fire,
generation of smoke or malfunction.
• PIONEER does not recommend that you
install or service your display yourself.
Ground wire
POWER AMP
Installing or servicing the product may
expose you to risk of electric shock or other
hazards. Refer all installation and servicing
of your display to authorized Pioneer service
personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wiring
to remain exposed.
Other devices
• Do not drill a hole into the engine
Metal parts of car's body
(Another electronic
compartment to connect the yellow lead
device in the car)
of the unit to the vehicle battery. Engine
vibration may eventually cause the insulation
to fail at the point where the wire passes from
Important
the passenger compartment into the engine
compartment. Take extra care in securing the
• When this unit is installed in a vehicle without
wire at this point.
ACC (accessory) position on the ignition switch,
• Make sure that wires will not interfere with
red cable must be wired to the terminal that can
moving parts of the vehicle, such as the
detect the operation of the ignition key. Otherwise,
gear shift, parking brake or seat sliding
battery drain may result.
mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work properly.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR
IS DESIGNED TO DETECT PARKED STATUS
ACC position
No ACC position
AND MUST BE CONNECTED TO THE POWER
SUPPLY SIDE OF THE PARKING BRAKE SWITCH.
• Use this unit with a 12-volt battery and negative
IMPROPER CONNECTION OR USE OF THIS
grounding only. Failure to do so may result in a
LEAD MAY VIOLATE APPLICABLE LAW AND MAY
fire or malfunction.
RESULT IN SERIOUS INJURY OR DAMAGE.
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
Connecting the unit
English
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
• When this unit is on, control signals are sent
through the blue/white cable. Connect this cable
to the system remote control of an external power
amp or the vehicle's auto-antenna relay control
terminal (max. 300 mA 12 V DC).
If the vehicle is equipped with a glass antenna,
connect it to the antenna booster power supply
terminal.
• Never connect the blue/white cable to the power
terminal of an external power amp.
Also, never connect it to the power terminal of the
auto antenna. Doing so may result in battery drain
or a malfunction.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.

Advertisement

Table of Contents

   Also See for Pioneer MVH-P7300

   Related Manuals for Pioneer MVH-P7300

   Summary of Contents for Pioneer MVH-P7300

  • Page 1 CAUTION limited. wire loosens or falls out, it could result in fire, MVH-P7300 — Use a fuse of the rating prescribed. generation of smoke or malfunction. • PIONEER does not recommend that you — Never wire the speaker negative cable directly install or service your display yourself. Ground wire POWER AMP to ground. Installing or servicing the product may — Never band together multiple speaker’s expose you to risk of electric shock or other negative cables.
  • Page 2 — No corte nunca el aislamiento del cable de PRECAUCIÓN — Tenez tous les câbles à l’écart des endroits alimentación de esta unidad para compartir cet appareil ou de tout autre appareil doivent être separado usando tornillos diferentes. Si el tornillo chauds, tels que les sorties du chauffage. la energía con otro equipo. La capacidad de connectés au véhicule séparément et avec des vis para el cable a tierra se afloja o se cae, puede • PIONEER no recomienda que sea usted ATTENTION — Ne faites pas passer le câble jaune par un corriente del cable es limitada. différentes. Si la vis du fil de masse se desserre ou provocar incendios, humo o averías. mismo quien instale o revise su pantalla. La tombe, il peut en résulter un incendie, de la fumée trou dans le compartiment du moteur pour le — Utilice un fusible con la capacidad • PIONEER ne vous recommande pas instalación o revisión del producto puede...
  • Page 3 Fuse (10 A) (sold separately) Hard-wired remote control adaptor can be connected To front output (sold separately). Power amp Front output IP-BUS cable (sold separately) Pioneer IP-BUS Subwoofer output To subwoofer accessories output (sold separately) Connect with RCA cables (sold separately) Yellow Connect to the constant 12 V supply terminal.
  • Page 4 À la sortie avant à fil (vendu séparément) à cette prise. Amplificateur de Sortie avant Câble IP-BUS puissance (vendu séparément) Accessoire Pioneer Sortie du caisson À la sortie du IP-BUS de grave caisson de grave (vendu séparément) Raccordez avec des câbles cinch (RCA) (vendus séparément)
  • Page 5 Amplificador de Cable IP-BUS Salida delantera potencia (vendido separadamente) Accesorios Salida de altavoz de A salida de altavoz IP-BUS Pioneer subgraves de subgraves (vendido separadamente) Conecte los cables RCA (vendidos separadamente) Amarillo Conecte al terminal de suministro de 12 V constante.
  • Page 6 Installation English Installation English Installation English Installation English Notes Installation with the mounting 3. Install the unit as illustrated. Removing the Unit Installing the microphone 2. Install the microphone clip on the 2. Install the microphone clip on the • Use commercially available parts when 1.
  • Page 7 Installation Français Installation Français Installation Français Installation Français Remarques Installation avec le manchon de 3. Installez l’appareil comme indiqué Enlèvement de l’appareil Installation du microphone 2. Fixez l’attache du microphone sur 2. Fixez l’attache du microphone sur sur la figure. 1.
  • Page 8 Instalación Español Instalación Español Instalación Español Instalación Español Notas Instalación con el manguito de 3. Instale la unidad según la Retirada de la unidad Instalación del micróphono 2. Instale la presilla de micrófono en 2. Instale la presilla de micrófono en montaje ilustración.

This manual is also suitable for:

Mvh-p8300bt

Comments to this Manuals

Symbols: 0
Latest comments: