Harken 2752 Installation Sheet

2 1 3 A S S Y W i n d w a r d S h e e t i n g A s s e m b l y P a r t s
A
B
B Important: Balls are loose
and will spill out when
cam caps are removed.
A
B
150SP Replacement Parts – Order Part No. 150KIT
150KIT. Contains:
No. Part No. Qty
A HSB86 1 Plastic Kit (Cam Caps and Washers) 2 Each
C
B 150BALLS 1 Ball Bearing Set (66)
C HSB56 2 Torsion Springs
1
2
5
6
213ASSY Windward Sheet Assembly Parts List
No. Part No.
1 HCP1949
2 150SP
3 201
Description 4 HFS107
5 HCP213
6 HCP218
7 HCP216
4
3
7
Qty Description
1 Top Plate with Sheaves
2 Cam Cleats (Modified)
2 Eyestraps, Low Profile
4 Screws 10-32X1.500 Slotted Trusshead (TH)
1 Bottom Plate
2 Slide Set
2 End Caps
Printed in USA. 4975/03-17-10
I N S T A L L A T I O N S H E E T
2744, 2745, 2746 Windward Sheeting Cars
2752 Windward Sheeting Adapter Kit
For use on Harken 2726, 2727, 2728, 2729,2730, 2731, 2734, 2735, 2736 Small Boat CB Cars
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: www.harken.com • E-mail: harken@harken.com
C B C A R S O N L Y R O L L O N C B T R A C K
Car Car Width Track
Small Boat 2 1 / " (57 mm) 373, 374, 2720, 2721, 2725, 2751
4
Note: Track not
shown actual size
373/2720/2751
374/2725
Mounting 2744, 2745, 2746 Windward Sheeting Cars
1. Position car at end of track, sheave side aft.
2. Gently roll car on track. Car should roll on easily, if
not check to make sure you are using CB track. Do not
remove ball retaining wires. Cars will not roll unless
they have retaining clips.
Important: Do not install a stand-up spring between
mainsheet block and windward car assembly.
Control Lines
2:1 Traveler Controls
1. Install a Harken 073 eyestrap near end of track.
2. Use / " or / " (6 mm or 8 mm) line.
1 5
4 16
3. Deadend control lines to eyestraps
at each end of track.
4. Reeve lines around sheaves
and through cam cleats.
2:1 Traveler Controls
3:1 Traveler Controls
3:1 Traveler Controls
1. Mount a 29 or 40 mm Carbo Block or 2740 control assembly at each end of track.
2. Remove two screws from sheave coverplate. Use Loctite ® on screws and mount becket tube.
3. Use / " or / " (6 mm or 8 mm) line. Pass end of line through becket tube and tie an overhand knot.
1 5
4 16
4. Reeve the line through block at end of track and back to car. Pass around sheave and into cleat.
Stop Knots
Always tie a stop knot. Tie knot where knot will catch in sheave and stop car before
it hits endstop or jams into track channel. Note: the 2746 1250 Series car will jam
on endstops unless stop knots are used. Use 446 endstop or stop knots.
2721
446 Endstop