Advertisement
Quick Links
Manual Language
Seneca line product
Product
Description
Contents:
PRELIMINARY WARNINGS
1.
PRELIMINARY INSTRUCTIONS
2.
GENERAL SPECIFICATIONS
3.
TECHNICAL SPECIFICATIONS
4.
INSTALLATION STANDARDS
5.
ELECTRICAL CONNECTIONS
6.
CONFIGURATIONS
7.
LED SIGNALLING ON THE FRONTAL
8.
PANEL
PURCHASE ORDER CODE
9.
MODULE LAYOUT
10.
DECOMMISSIONING AND DISPOSAL
11.
Factory
Site
Mail
This document is property of SENECA srl. Duplication and reproduction are forbidden, if not authorized.
The content of the present documentation refers to products and technologies described in it. All
technical data contained in the document may be modified without prior notice. Content of this
documentation is subject to periodical revision.
INSTALLATION MANUAL
Multifunction controller
MI004061-E.DOCX
with Straton PLC, I/O and GPRS modem on board
Headquarters: Via Austria 26
35127 – Z.I. - Padova – IT
Phone: +39.049.8705355- 8705355
Technical support:
Product Informations:
ENGLISH
Z-PC
Z-miniRTU
Seneca srl
Fax +39 049.8706287
www.seneca.it
support@seneca.it
sales@seneca.it
ENGLISH 1/8
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Seneca Z-miniRTU
Summary of Contents for Seneca Z-miniRTU
- Page 1 Product Informations: sales@seneca.it This document is property of SENECA srl. Duplication and reproduction are forbidden, if not authorized. The content of the present documentation refers to products and technologies described in it. All technical data contained in the document may be modified without prior notice. Content of this documentation is subject to periodical revision.
- Page 2 • Insulation 3000 VA between power supply and relays contacts, 1500 VA between power supply and other circuits • Easy power supply and serial communication wiring through Seneca IEC EN 60715 DIN rail bus • LEDs signaling: digital inputs, digital outputs, Ethernet activity and GSM activity •...
- Page 3 Analog inputs 2 channels: mA or VC configurable, resolution: 16 bit, inputs protection: 40V 25mA, Voltage input: 0 – 30 V / accuracy 0,1% of the full scale Current input: 0 – 20 mA / accuracy 0,1% of the full scale Communication ports RS485 COM2 IDC10 rear port...
- Page 4 DIN rail support. The figure shows the meaning of the terminal blocks and the position of the DIP- switch in the Seneca IEC EN 60715 DIN rail accessory. GNDSHLD: Shield to protect the connection cables against interference (recommended).
- Page 5 Digital Input 1, 2, 3 and 4 Digital output 1 Digital output 2 Free contacts output The Z-miniRTU module has two digital outputs with free contacts The figures show the internal relay contacts available. MI004061-E.DOCX ENGLISH 5/8...
- Page 6 4.5mm. Connection of RJ45 ETHERNET Z-miniRTU module has an Ethernet port with RJ45 connector, on the front of the module, for TCP-IP communications. Note: Inserting the RJ45 10/100 BaseT Ethernet plug make sure that the connector is securely latched, or before inserting the cable into the RJ45 connector, remove the protective rubber.
- Page 7 Digital Input 3: De-energized (open contact) Digital Input 4: Energized (closed contact) DI4 Red Digital Input 4: De-energized (open contact) Z-miniRTU ON, PLC program present PWR/STS Green Z-miniRTU OFF Slow blinking Z-miniRTU ON, PLC program not present SD/STS Red Blinking...
- Page 8 MODULE LAYOUT For the Z-miniRTU configuration, use the EASY SETUP software available for download, at: www.seneca.it/products/z-minirtu For further information on the product, refer to the USER MANUAL available for download, at: www.seneca.it/products/z-minirtu DECOMMISSIONING AND DISPOSAL Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
Need help?
Do you have a question about the Z-miniRTU and is the answer not in the manual?
Questions and answers