Download Table of Contents Print this page
Craftsman 11779 - 7.2V NiCd Screwdriver Operator's Manual

Craftsman 11779 - 7.2V NiCd Screwdriver Operator's Manual

7.2 volt cordless screwdriver two speed/reversible


Model No.
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
Helpline: 1 =800=932=3188
Sears, Roebuck
and Co., 3333 Beverly Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page:
Save this manual
for future
11-05-07 (REV:00)


Table of Contents

Summary of Contents for Craftsman 11779 - 7.2V NiCd Screwdriver

  • Page 1 Craftsman Consumer Helpline: 1 =800=932=3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: 987000-297 Save this manual for future reference 11-05-07 (REV:00)
  • Page 2 SEARS STORE OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR FREE REPLACEMENT. If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
  • Page 3 safety shoes, hard hat, or hearing protection used for WARNING! Read all instructions. Failure to fol- appropriate conditions will reduce personal injuries. low all instructions listed below may result in electric [] Avoid accidental starting. Ensure the switch is in shock, fire and/or serious injury.
  • Page 4 Use the power tool, accessories and tool bits etc., Shorting the battery terminals together may cause in accordance with these instructions and in the burns or a fire. manner intended for the particular type of power Under abusive conditions, liquid may be ejected tool, taking into account the working conditions...
  • Page 5 [] An extension cord should not be used unless WARNING! READ AND UNDERSTAND ALL absolutely necessary. Use of improper extension INSTRUCTIONS. Failure to follow all instructions cord could result in a risk of fire and electric shock. If listed below, may result in electric shock, fire and/or extension cord must be used, make sure: serious personal injury.
  • Page 6 Someofthefollowing symbols maybeusedonthis product. P lease studythemandlearn theirmeaning. Proper interpretation ofthesesymbols willallowyouto operate the product b etterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Current Amperes Hertz Frequency (cycles per second) Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current =.--=.#_...
  • Page 7 If you do not understand the warnings and to your nearest SEARS PARTS AND REPAIR SERVICE instructions in the operator's manual, do not use this CENTER for repair. When servicing, use only identical product. Call the Craftsman Consumer Helpline at replacement parts. 1-800-932-3188 for assistance.
  • Page 8 PRODUCT SPECiFiCATiONS Collet ............1/4 in. Hex Shank Speeds ..........200/600 r/min. (RPM) Clutch .............. 24 Positions Motor ..............7.2 Volt DC Switch ..........Rocker Type/Reversible TWO-SPEED GEAR TRAIN (HI&O) TORQUE ADJUSTMENTRiNG STICK/PISTOL ROTATION BUTTON COLLET LEDLIGHT BiT STORAGE CHARGER LIGHT SCREWDRIVER BiTS Fig.
  • Page 9 KNOWYOURSCREWDRIVER STICK/PISTOL COMBINATION SCREWDRIVER See Figure 1. The screwdriver has been designed so that it can be operated as a stick screwdriver or a pistol screwdriver. The safe use of this product requires an understanding of the information on the product and in this operator's SWITCH manual as well as a knowledge of the project you are The screwdriver is equipped with a rocker type switch...
  • Page 10 [] After normal usage, a minimum of 10 hours of charging WARNING: Do not allow familiarity with products to time is required to fully charge screwdriver. make you careless. Remember that a careless [] Do not place charger in an area of extreme heat or fraction of a second is sufficient to inflict serious cold.
  • Page 11 ADJUSTING BIT STORAGE TORQUE See Figure 7. See Figure 5. There are twenty-four torque indicator settings located on When not in use, bits provided with the screwdriver can the front of the screwdriver. be placed in the storage area located on the front of the screwdriver.
  • Page 12 MAINTENANCE WARNING: When servicing, use only identical Avoid using solvents when cleaning plastic parts. Most Craftsman replacement parts. Use of any other part plastics are susceptible to damage from various types of may create a hazard or cause product damage.
  • Page 13 The use of attachments accessories not recommended can result in serious personal injury. CRAFTSMAN 7.2 VOLT SCREWDRIVER MODEL NO. 315.117790 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your SOREWORIVER or when ordering repair parts.
  • Page 14 Your Home For expert troubleshooting and home solutions advice: For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.

This manual is also suitable for:


Table of Contents