Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Kogan KATVULT80LA
Summary of Contents for Kogan KATVULT80LA
- Page 1 ULTRA SLIM MICRO-GAP FIXED TV WALL MOUNT (SUITABLE FOR 37-85" TVS) KATVULT80LA...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS Read the entire user guide before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, contact your local distributor for assistance. CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury. - Page 4 COMPONENTS A Wall Mount (x1) B TV Bracket (x2) C Wall Bracket (x2) D Kickstand (x1) E Left Endcap (x1) F Right Endcap (x1) G Spirit Level (x1) H Foam Pad (x4) I Foam Pad (x4) M-A M6x14 M-B M8x16 M-C M6x30 J Allen Key (3mm) (x1)
- Page 5 ASSEMBLY Tools Required Stud finder Pen/pencil Drill & Drill Bit Ratchet & Phillips head Sockets screwdriver Step 1: Separate the wall mount (A) into (A2) & (A1).
- Page 6 Step 2: • Remove the fasteners from the end of the wall mount (A) and slide the 2 wall brackets (C) into the channel. Replace the fasteners. • Attach the spirit level (G) to the top of the wall mount (A).
- Page 7 Step 3: Using a pencil and spirit level (G), mark the desired position for the mount on your wall, using the wall mount (A) as a template for the hole positions. Note: When using the spirit level, ensure the bubble is centred as per the image shown below. If mounting on dry wall or plaster-board, use a stud finder first to check positions of wall studs and ensure the position is free from electrical wiring.
- Page 8 Step 4: Drywall / plaster: Attach the wall mount (A) to the wall using the 2 ST6.3x55 screws (W-A) and D6 washers (W-C). Ensure a 5mm excess is left between the head of the screw and the wall surface. Do not use wall anchors. Masonry / concrete: Insert wall anchors (W-B) into all 3 drilled holes.
- Page 9 Step 5: • Set the distance of the wall brackets (C) depending on the size of your TV. • Replace part (A2) back onto the wall mount (A) and attach the endcaps (E) & (F). to the ends of wall mount (A).
- Page 10 Step 6: Align the brackets (B) with your TV’s VESA holes and secure using supplied screws (“M-” set), Washer (M-E) and spacers (M-F, M-G) depending on required length. Note: For TV’s 55” and smaller, attach the brackets (B) to the lower two VESA holes, if the TV doesn’t fully cover the wall mount (A).
- Page 11 Step 7: If a corresponding hole is available on your TV, attach the kickstand (D) and secure using supplied screws (“M-” set), Washer (M-E) and spacers (M-F, M-G) depending on required length. Too long Too short...
- Page 12 Step 8: Attach the appropriate EVA pads (H) & (I) to the rear of the TV to fill the wall-to-TV gap.
- Page 13 Step 9: • Carefully hook the TV with brackets and optional kickstand installed onto the wall mount. 2 people should carry the TV to prevent damage. Note: Ensure the hooks on the TV brackets are completely seated in the wall brackets. •...
- Page 14 Step 10: Removing the TV from the Wall Mount To remove, using the assistance of another person, carefully lift the TV upwards and unhook TV brackets from the wall brackets. IMPORTANT: Do not attempt to remove the TV by yourself...
- Page 15 NOTES...
- Page 16 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com...
Need help?
Do you have a question about the KATVULT80LA and is the answer not in the manual?
Questions and answers